MR VACUTAP VM-Ex Installation And Commissioning Instructions Download Page 118

Page: 118 / 210

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

118

5293079/01 EN

VACUTAP

VM-Ex

2. Insert lifting gear in the brackets provided on the diverter switch insert car-

rier plate and position vertically above the diverter switch insert.

Figure 123: Brackets on carrier plate

3. Ensure that diverter switch insert is in the final end position on the same

side as when it was removed (side A or side B). The vacuum interrupter is
closed on the side that is in the final end position. In the example in the
appendix, side B is in the final end position, see appendix.

4. By turning the coupling tube, align it in such a manner that the red trian-

gles on the coupling tube and carrier plate match up.

Figure 124: Coupling tube

Summary of Contents for VACUTAP VM-Ex



















































































































































































































Search results

Summary of Contents for VACUTAP VM-Ex

Reviews:

Related manuals for VACUTAP VM-Ex

Brands by name

Popular brands

MR VACUTAP VM-Ex, Installation And Commissioning Instructions

Search results

Summary of Contents for VACUTAP VM-Ex

Reviews:

Related manuals for VACUTAP VM-Ex

Brands by name

Popular brands