MR VACUTAP VM-Ex Installation And Commissioning Instructions Download Page 114

Page: 114 / 210

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

114

5293079/01 EN

VACUTAP

VM-Ex

5.4.7.3 Connecting on-load tap-changer to top part of on-load tap-changer

head

NOTICE

Incorrectly lifting the on-load tap-changer will damage it!

If the connection screws of the supporting flange are used to lift the on-load
tap-changer, the screws may be damaged, which makes it impossible to
properly screw the on-load tap-changer and the on-load tap-changer head
together!

► Always lift the on-load tap-changer with the specified lifting traverse, and

never with the connection screws of the supporting flange.

1. Insert lifting traverse in on-load tap-changer head.

Figure 116: Lifting traverse

Summary of Contents for VACUTAP VM-Ex



















































































































































































































Search results

Summary of Contents for VACUTAP VM-Ex

Reviews:

Related manuals for VACUTAP VM-Ex

Brands by name

Popular brands

MR VACUTAP VM-Ex, Installation And Commissioning Instructions

Search results

Summary of Contents for VACUTAP VM-Ex

Reviews:

Related manuals for VACUTAP VM-Ex

Brands by name

Popular brands