MR VACUTAP VM-Ex Installation And Commissioning Instructions Download Page 142

Page: 142 / 210

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

142

5293079/01 EN

VACUTAP

VM-Ex

5. Position the wire for the terminal box cover and affix using the slotted

head screw.

Figure 164: Terminal box cover

6. Attach the terminal box cover and secure with screws.

Figure 165: Terminal box cover

5.5.2.3 Installing protective relay in piping

Ensure the following for installation and proper function of the protective re-
lay:

1. Ensure that there are no foreign bodies in the piping or in the oil conserva-

tor.

2. Install protective relay such that it can be easily accessed for subsequent

maintenance work.

3. Install protective relay with good support and free from vibrations.

4. The test buttons must be at the top.

5. The interior diameter of the piping must be at least 25 mm.

Summary of Contents for VACUTAP VM-Ex



















































































































































































































Search results

Summary of Contents for VACUTAP VM-Ex

Reviews:

Related manuals for VACUTAP VM-Ex

Brands by name

Popular brands

MR VACUTAP VM-Ex, Installation And Commissioning Instructions

Search results

Summary of Contents for VACUTAP VM-Ex

Reviews:

Related manuals for VACUTAP VM-Ex

Brands by name

Popular brands