MR VACUTAP VM-Ex Installation And Commissioning Instructions Download Page 53

Page: 53 / 210

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

5293079/01 EN

VACUTAP

VM-Ex

7. Screw the on-load tap-changer head to the mounting flange.

Figure 32: Screwing the on-load tap-changer head to the mounting flange

8. Reattach the connecting leads for an on-load tap-changer with potential

connection unit or an on-load tap-changer with 3W/2W/3G change-over
selector.

Figure 33: Fitting connecting leads

5.3.3 Connecting the tap winding and on-load tap-changer take-off

lead

NOTICE

Damage to the on-load tap-changer!

Connecting leads that place mechanical strain on the on-load tap-changer
will damage the on-load tap-changer.

► Establish connections carefully.

► Do not twist connection contacts.

► Connect connecting leads without warping or deforming.

► If necessary, use an expansion loop for connecting leads.

► Fit screening caps provided to screw connections.

Summary of Contents for VACUTAP VM-Ex



















































































































































































































Search results

Summary of Contents for VACUTAP VM-Ex

Reviews:

Related manuals for VACUTAP VM-Ex

Brands by name

Popular brands

MR VACUTAP VM-Ex, Installation And Commissioning Instructions

Search results

Summary of Contents for VACUTAP VM-Ex

Reviews:

Related manuals for VACUTAP VM-Ex

Brands by name

Popular brands