MR VACUTAP VM-Ex Installation And Commissioning Instructions Download Page 181

Page: 181 / 210

6 Commissioning

Maschinenfabrik Reinhausen GmbH 2020

181

5293079/01 EN

VACUTAP

VM-Ex

2. Fill on-load tap-changer with new insulating fluid using one of the two free

pipe connections of the on-load tap-changer head.

Figure 213: Pipe connections S and R

3. Take an insulating fluid sample from the oil compartment.

4. Record the temperature of the sample immediately after the sample is

taken.

5. Determine the dielectric strength and water content at a sample tempera-

ture of 20°C ± 5°C. The dielectric strength and water content must comply
with the limit values [

►

Section 8.3, Page 193] specified in the technical

data.

6.3.2 Bleeding on-load tap-changer head and suction pipe

6.3.2.1 Bleeding on-load tap-changer head

1. Open all forward valves and return valves in the pipe system.

Summary of Contents for VACUTAP VM-Ex



















































































































































































































Search results

Summary of Contents for VACUTAP VM-Ex

Reviews:

Related manuals for VACUTAP VM-Ex

Brands by name

Popular brands

MR VACUTAP VM-Ex, Installation And Commissioning Instructions

Search results

Summary of Contents for VACUTAP VM-Ex

Reviews:

Related manuals for VACUTAP VM-Ex

Brands by name

Popular brands