MR VACUTAP VM-Ex Installation And Commissioning Instructions Download Page 178 | Manualshive

Page: 178 / 210

background image

6 Commissioning

Maschinenfabrik Reinhausen GmbH 2020

178

5293079/01 EN

VACUTAP

®

VM-Ex

6.2 Transporting transformer to the operating site

NOTICE

Damage to motor-drive unit!

Damage to the motor-drive unit due to condensate in protective housing of
motor-drive unit.

► Always keep protective housing of the motor-drive unit tightly closed.

► In the event of downtime lasting more than 8 weeks prior to initial com-

missioning, connect and operate the anti-condensation heater in the mo-
tor-drive unit. If this is not possible, place a sufficient amount of desiccant
in the protective housing.

6.2.1 Transport with drive removed

1. Ensure that the drive and the on-load tap-changer are in the adjustment

position.

2. Remove the drive.

3. Do not actuate the drive while the on-load tap-changer is uncoupled and

do not turn the output shaft.

4. Do not actuate an on-load tap-changer which is uncoupled and do not turn

its drive shaft.

5. Transport the drive to the installation site in the MR delivery packaging.

6. Fit the drive [

Section 5.5.3, Page 148] and the drive shaft to the trans-

former at the installation site.

6.2.2 Transport with full transformer tank and without oil conservator

Attach a connecting lead between the on-load tap-changer's oil compartment
and the transformer tank if the transformer has been transported with a full
tank and without an oil conservator.

► Establish a connecting lead on the on-load tap-changer head between

connections E2 and Q or E2 and R.

Figure 211: Connecting lead

«
...
176
177
178
179
180
...
»

Summary of Contents for VACUTAP VM-Ex



















































































































































































































Reviews:

No comments

Related manuals for VACUTAP VM-Ex

Brand: e-survey Pages: 54

Brand: fadini Pages: 20

Brand: Twiflex Pages: 5

Phastite PH-8-HANDTOOL

Brand: Parker Pages: 10

Z45-D160.05 S3A

Brand: Jäger Pages: 40

CDC-TW-0502-1-ACB

Brand: D+H Pages: 16

Brand: Jäger Pages: 36

Brand: WCS Pages: 22

Brand: SAINT-GOBAIN Pages: 21

Brand: Facom Pages: 4

Brand: Azbil Pages: 2

BOS R090K-U-RX10-S49 Series

Brand: Balluff Pages: 28

Brand: FILLON TECHNOLOGIES Pages: 28

Brand: Graco Pages: 76

ROLLON ELM 110 SP

Brand: Timken Pages: 9

Modular Fume Hood

Brand: Lincoln Electric Pages: 28

AutoJet AccuCoat HD15

Brand: Spraying Systems Co Pages: 18

Brand: ABB Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands