Moxa Technologies ioLogik E2210 User Manual Download Page 5

Page: 5 / 144

LCM Controls ...................................................................................................................................... A-2

LCM Options....................................................................................................................................... A-2

Used Network Port Numbers ............................................................................................................. B-1

ioLogik E2200 Smart Ethernet Remote I/O Device Network Port Usage ...................................................... B-1

Factory Default Settings .................................................................................................................... C-1

Cable Wiring ...................................................................................................................................... D-1

Device Wiring Diagrams ..................................................................................................................... D-2

Analog Input .............................................................................................................................. D-2

Analog Output ........................................................................................................................... D-2

Digital Input Dry Contact ............................................................................................................. D-2

Digital Input Wet Contact ............................................................................................................ D-3

RTD Input Wiring ............................................................................................................................... D-5

Thermocouple Input Wiring ................................................................................................................. D-6

Input and Output Terminal ................................................................................................................ E-1

ioLogik E2210 .................................................................................................................................... E-2

ioLogik E2212 .................................................................................................................................... E-2

ioLogik E2214 .................................................................................................................................... E-2

ioLogik E2240 .................................................................................................................................... E-3

ioLogik E2242 .................................................................................................................................... E-3

ioLogik E2260 .................................................................................................................................... E-3

ioLogik E2262 .................................................................................................................................... E-4

Accuracy ........................................................................................................................................... F-1

Calibration ......................................................................................................................................... F-1

Simple Verification at Your Site ............................................................................................................ F-1

Verification with RTD Sensor ......................................................................................................... F-1

Verification with Precision Resistor ................................................................................................. F-1

CGI Commands.................................................................................................................................. G-1

ioLogik E2210 ................................................................................................................................... G-2

ioLogik E2212 ................................................................................................................................... G-6

ioLogik E2214 .................................................................................................................................. G-10

ioLogik E2240 .................................................................................................................................. G-12

ioLogik E2242 .................................................................................................................................. G-14

ioLogik E2260 .................................................................................................................................. G-19

ioLogik E2262 .................................................................................................................................. G-22

SNMP Agents with MIB II, RS-232-like Groups ............................................................................... H-1

ioLogik E2242 ................................................................................................................................... H-1

Modbus/TCP Address Mappings ......................................................................................................... I-1

ioLogik E2210 Modbus Mapping ............................................................................................................ I-2

ioLogik E2212 Modbus Mapping ........................................................................................................... I-15

ioLogik E2214 Modbus Mapping ........................................................................................................... I-37

ioLogik E2240 Modbus Mapping ........................................................................................................... I-47

ioLogik E2242 Modbus Mapping ........................................................................................................... I-57

ioLogik E2260 Modbus Mapping ........................................................................................................... I-76

ioLogik E2262 Modbus Mapping ........................................................................................................... I-81

Summary of Contents for ioLogik E2210
















































































































































Search results

Summary of Contents for ioLogik E2210

Reviews:

Moxa Technologies ioLogik E2210, User Manual, Page: 5 / 144

Search results

Summary of Contents for ioLogik E2210

Reviews: