manualshive.com logo in svg

Mitsubishi ECLIPSE CROSS 2017, Owner'S Manual

The Mitsubishi ECLIPSE CROSS 2017 is a sleek and stylish crossover SUV that offers a comfortable and enjoyable driving experience. For those who own this vehicle, finding the Owner's Manual is essential. You can download the manual for free from manualshive.com to ensure you have all the information you need to maintain and operate your ECLIPSE CROSS.

Share
Download
background image

The  system  automatically  shifts  from  the
“ON”  state  to  the  standby  state  if  all  of  the
following conditions are simultaneously met.
The   indicator on the information screen in
the multi-information display will be changed
from white to green.

l

The  vehicle  speed  is  approximately
65 km/h (40 mph) or higher.

l

The turn-signal lever is not operated.

l

The hazard lamp is not activated.

l

Environmental  conditions  are  adequate
for  the  system  to  recognize  the  lane
markings on both sides.

l

The system has been placed in the “ON”
state.

(white)

(green)

NOTE

l

The  system  stays  in  the  “ON”  state  for  ap-
proximately 7 seconds after the hazard lamp
has stopped flashing or the turn-signal lever
has returned to the home position.

Lane departure warning

E00638600079

A  buzzer  sounds  intermittently  and  the  indi-
cation of “LANE DEPARTURE” appears on
the  information  screen  of  the  multi-informa-
tion display,   and the indicator starts flash-
ing  in  yellow  when  your  vehicle  is  about  to
leave or has left the lane in the standby mode.

NOTE

l

If the warning continues for approximately 3
seconds or more, the system switches to the
standby mode before the warning stops.

NOTE

l

If  the  lane  markers  are  only  on  one  side  of
the road, the LDW will operate only for the
appropriate  side  where  the  lane  marker  is
drawn.

System problem warning

E00635901049

If  there  is  a  malfunction  in  the  system,  a
warning  will  appear  on  the  information
screen  of  the  multi-information  display  de-
pending on the situation.

Too hot or cold sensor

E00638700067

The  alarm  shown  below  is  displayed  if  the
system becomes temporarily unavailable due
to  a  too  high  or  low  temperature  of  the  sen-
sor.
If  the  temperature  of  the  sensor  reaches  the
predetermined value, the system automatical-
ly recovers the normal state.
If  the  alarm  continues  showing,  there  is  a
possibility that the LDW has a malfunction.
Contact  a  MITSUBISHI  MOTORS  Author-
ized  Service  Point  for  inspection  of  the  sys-
tem.

Lane Departure Warning (LDW)*

6-102

OGKE18E1

Starting and driving

6

Summary of Contents for ECLIPSE CROSS 2017



























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ECLIPSE CROSS 2017

Camcar 40052 Mounting Instructions preview
40052
Brand: Camcar Pages: 6
Jeda Wireless Pad Manual preview
Wireless Pad
Brand: Jeda Pages: 8
Jeep 2009 Wrangler Owner'S Manual preview
2009 Wrangler
Brand: Jeep Pages: 496
Kargo Master 80070 Assembly Lnstructions preview
80070
Brand: Kargo Master Pages: 13
Kargo Master 4A96L Installation Manual preview
4A96L
Brand: Kargo Master Pages: 21
Kargo Master 40201 Installation Manual preview
40201
Brand: Kargo Master Pages: 4
Rightline Gear Car Top Duffle Bag Setup Manual preview
Car Top Duffle Bag
Brand: Rightline Gear Pages: 2
REVCAMUK MON16AHD Instructions preview
MON16AHD
Brand: REVCAMUK Pages: 4
Thule 1308 Instructions Manual preview
1308
Brand: Thule Pages: 8
P-Invent Troller User Manual preview
Troller
Brand: P-Invent Pages: 4
Webasto Telestart T91 Installation Instructions Manual preview
Telestart T91
Brand: Webasto Pages: 18
ULTIMATE SPEED 279746 Assembly And Safety Advice preview
279746
Brand: ULTIMATE SPEED Pages: 6
Buick 2015 LaCrosse Getting To Know Manual preview
2015 LaCrosse
Brand: Buick Pages: 20
Smappee EVB-1332-BL-E Installation Manual preview
EVB-1332-BL-E
Brand: Smappee Pages: 28
ACV 381190-37-1 Installation Manual preview
381190-37-1
Brand: ACV Pages: 2
TERAFLEX 1365000 Manual preview
1365000
Brand: TERAFLEX Pages: 18
Witter DT144AU Fitting Instructions preview
DT144AU
Brand: Witter Pages: 2
Honda 2004 Civic Si Owner'S Manual preview
2004 Civic Si
Brand: Honda Pages: 219

Brands by name

Popular brands

Load more brands