Mitsubishi ECLIPSE CROSS 2017 Owner'S Manual Download Page 236 | Manualshive

Page: 236 / 538

background image

To activate

E00633601114

Accelerate  or  decelerate  to  your  desired
speed,  and  push  down  the  “SET  -”  switch
(B).  The  Speed  Limiter  memorizes  the  cur-
rent vehicle speed when you release the “SET
-” switch (B). Now, the Speed Limiter starts
controlling  in  order  not  to  exceed  the  set
speed.

If the current vehicle speed is lower than ap-
proximately 30 km/h (20 mph) (settable min-
imum speed), the set speed is set at approxi-
mately 30 km/h (20 mph).
The set speed is displayed in the combination
meter.
And, control state “LIMIT” is displayed in
the combination meter.

To increase the set speed

E00633700017

By using the RES + switch

E00633801116

Push up the “RES +” switch continuously.

Then the set speed displayed in the combina-
tion meter is gradually increased.
If the set speed reaches your desired speed,
release the “RES +” switch (C).

The set speed is increased each approximate-
ly 5 km/h (3 mph) per approximately 0.5 sec-
ond.
If  a  driver  wants  to  increase  the  set  speed  a
little,  push  up  “RES  +”  switch  for  less  than
approximately 0.5 second and release it.
The  set  speed  is  increased  1  km/h  (1  mph)
each taps.

By using the CANCEL switch,
the accelerator pedal and the
SET - switch

E00633901117

Press the “CANCEL” switch (D) to deacti-
vate the Speed Limiter.

Control state “LIMIT” is disappeared and
change control state “LIMIT OFF” in the
combination meter.

Speed Limiter*

6-62

OGKE18E1

Starting and driving

6

«
...
234
235
236
237
238
...
»

Summary of Contents for ECLIPSE CROSS 2017



























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ECLIPSE CROSS 2017

Brand: Baja Designs Pages: 6

Brand: Yakima Pages: 8

QuadraTop Adventure Top S

Brand: Quadratec Pages: 20

Brand: AccuAir Pages: 40

Brand: Peak Pages: 10

Brand: Kia Pages: 54

Brand: Metra Electronics Pages: 2

Brand: muth Pages: 10

Brand: Condor Pages: 2

BTFREQ PRO BTFMPD3SR

Brand: Scosche Pages: 16

Brand: Nuna Pages: 17

Brand: AEM Pages: 27

Brand: E&G Classics Pages: 4

INDICA eV2 XETA CNG

Brand: TATA Motors Pages: 24

Brand: PAC Pages: 5

Brand: Percon Pages: 49

Brand: Pontiac Pages: 20

Brand: Dakota Digital Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands