manualshive.com logo in svg

Mitsubishi ECLIPSE CROSS 2017, Owner'S Manual

The Mitsubishi ECLIPSE CROSS 2017 is a sleek and stylish crossover SUV that offers a comfortable and enjoyable driving experience. For those who own this vehicle, finding the Owner's Manual is essential. You can download the manual for free from manualshive.com to ensure you have all the information you need to maintain and operate your ECLIPSE CROSS.

Share
Download
background image

NOTE

l

When  the  selector  lever  is  other  than  “P”
(Park)  position,  if  you  try  to  release  the
Electric  parking  brake  without  depressing
the brake pedal, the warning display will ap-
pear.

l

If  you  start  driving  without  releasing  the
Electric  parking  brake,  the  warning  display
will appear.

l

If  the  driver’s  foot  contacts  the  accelerator
pedal in the condition that the Electric park-
ing  brake  can  be  released  by  an  automatic
operation, the Electric parking brake may be
released automatically.

Warning lamp/display

Warning lamp (yellow)

Warning display

If  there  is  a  malfunction  in  the  system,  the
warning  lamp  will  come  on.  In  addition,  the
warning  display  appears  on  the  information
screen in the multi-information display.
Under  normal  conditions,  the  warning  lamp
only  comes  on  when  the  ignition  switch  is
turned to the “ON” position or the operation
mode  is  put  in  ON  and  goes  off  a  few  sec-
onds later.

CAUTION

l

When  the  Electric  parking  brake  warning
lamp (yellow) does not illuminate or remains
illuminated  when  the  ignition  switch  is
turned to the “ON” position or the operation
mode is put in ON, or comes on while driv-
ing,  the  Electric  parking  brake  may  not  be
applied or released. Immediately contact the
nearest MITSUBISHI MOTORS Authorized
Service  Point.  For  details,  refer  to  “Electric
parking  brake  warning  light  (yellow)”  on
page 5-47.
When  parking  your  vehicle  while  the  Elec-
tric parking brake warning lamp (yellow) is
illuminated,  park  the  vehicle  on  level  and
stable ground, move the selector lever to the
“P”  (PARK)  position  and  place  chocks,
blocks  or  stones  behind  and  in  front  of  the
tyres to prevent the vehicle from moving.

Parking

E00600602834

To park the vehicle, firmly apply the parking
brake, and then move the gearshift lever to 1

st

or “R” (Reverse) position for vehicles equip-
ped with M/T, or set the selector lever to “P”
(PARK)  position  for  vehicles  equipped  with
CVT.

Parking on a hill

To  prevent  the  vehicle  from  rolling,  follow
these procedures:

Parking

6-08

OGKE18E1

Starting and driving

6

Summary of Contents for ECLIPSE CROSS 2017



























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ECLIPSE CROSS 2017

Jeep Cherokee 16 1982 Technical & Service Manual preview
Cherokee 16 1982
Brand: Jeep Pages: 1311
Kia 2016 Cadenza Owner'S Manual preview
2016 Cadenza
Brand: Kia Pages: 419
CITROEN C8 NaviDrive Manual preview
C8 NaviDrive
Brand: CITROEN Pages: 52
Condor T-RAMP Quick Start Manual preview
T-RAMP
Brand: Condor Pages: 2
Thule 1430 Kit Instructions Manual preview
1430 Kit
Brand: Thule Pages: 8
tams elektronik FCS-4 Manual preview
FCS-4
Brand: tams elektronik Pages: 19
Great Wall WEY VV5 Service Manual preview
WEY VV5
Brand: Great Wall Pages: 18
WIX WP9378 Installation Instruction preview
WP9378
Brand: WIX Pages: 2
Westin 22-1065 Instructions preview
22-1065
Brand: Westin Pages: 3
Jaeger 12020523 Fitting Instructions Manual preview
12020523
Brand: Jaeger Pages: 11
A-Tach Mounts 50232 Instructions preview
50232
Brand: A-Tach Mounts Pages: 2
Bestop 51252 Installation Instructions preview
51252
Brand: Bestop Pages: 4
Edelbrock 460 Ford Installation Instructions preview
460 Ford
Brand: Edelbrock Pages: 2
Carcomm CMPC-22 Fujitsu-Siemens PocketLoox 410 Installation Manual preview
CMPC-22 Fujitsu-Siemens PocketLoox 410
Brand: Carcomm Pages: 2
Ford transit connect 2012 User Manual preview
transit connect 2012
Brand: Ford Pages: 299
Smappee EVB-1332-BL-E Installation Manual preview
EVB-1332-BL-E
Brand: Smappee Pages: 28
Federal Signal Corporation HighLighter Installation And Programming preview
HighLighter
Brand: Federal Signal Corporation Pages: 20
PEUGEOT 5008 2017 Handbook preview
5008 2017
Brand: PEUGEOT Pages: 404

Brands by name

Popular brands

Load more brands