Mitsubishi ECLIPSE CROSS 2017 Owner'S Manual Download Page 21 | Manualshive

Page: 21 / 538

background image

1. Lock button

The lock button must be
pushed while the brake
pedal is depressed to
move the selector lever.

The lock button must be
pushed to move the se-
lector lever.

The lock button need
not be pushed to move
the selector lever.

Selector lever positions

“P” PARK

This position locks the transmission to pre-
vent the vehicle from moving. The engine
can be started in this position.

“R” REVERSE

This position is to back up.

“N” NEUTRAL

At this position the transmission is disengag-
ed.

“D” DRIVE

This position is for normal driving.
Refer to “INVECS-III CVT with 8-step
Sports Mode” on page 6-30

Multi information display

E08501201330

Always stop the vehicle in a safe place before
operating.
The following information is included on the
multi-information display: warnings, odome-
ter, tripmeter, average and instant fuel con-
sumption, average speed, etc.

1- mark display screen

2- Information screen

Interrupt display screen

3- Door ajar warning display screen

5- " " Interrupt display screen

Refer to “Multi-information display” on
page 5-02.

Head Up Display (HUD)*

E08502900021

The Head Up Display (HUD) shows informa-
tion on a transparent display so that you can
easily check meter information (vehicle
speed, navigation instructions, etc.) while
looking ahead when driving.

Example

1. Display
2. Speed display screen
3. Information display screen

Quick guide

1-19

OGKE18E1

Overview/Quick guide

1

«
...
19
20
21
22
23
...
»

Summary of Contents for ECLIPSE CROSS 2017



























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ECLIPSE CROSS 2017

Brand: AC Schnitzer Pages: 16

Brand: Uniden Pages: 16

Brand: Uniden Pages: 20

Brand: Metra Electronics Pages: 4

REARSIGHT OnStar 250-8822

Brand: Rostra Pages: 2

Brand: Subaru Pages: 99

Brand: Dometic Pages: 158

DELTA DL FIX 209FP

Brand: Menabo Pages: 8

Brand: Ranger design Pages: 24

Brand: Westin Pages: 2

Brand: Toyota Pages: 165

Brand: BrandMotion Pages: 12

Brand: Painless Performance Pages: 16

Brand: EUFAB Pages: 8

Brand: Genesis Pages: 29

Brand: Nav TV Pages: 8

Brand: Lincoln Pages: 370

Brand: Scion Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands