manualshive.com logo in svg

Mitsubishi ECLIPSE CROSS 2017, Owner'S Manual

The Mitsubishi ECLIPSE CROSS 2017 is a sleek and stylish crossover SUV that offers a comfortable and enjoyable driving experience. For those who own this vehicle, finding the Owner's Manual is essential. You can download the manual for free from manualshive.com to ensure you have all the information you need to maintain and operate your ECLIPSE CROSS.

Share
Download
background image

To release

Manual operation

1. Make sure that the ignition switch or the

operation mode is ON.

2. Press  down  the  Electric  parking  brake

switch while depressing the brake pedal.

Automatic operation

When  the  accelerator  pedal  is  depressed
slowly  while  all  of  the  following  conditions
are  met,  the  Electric  parking  brake  is  auto-
matically released.

l

The engine is running.

l

The  selector  lever  is  in  the  “D”  (Drive)
or the “R” (Reverse) position.

l

The driver’s seat belt is fastened.

When  the  Electric  parking  brake  is  released,
the brake warning lamp (red) and the indica-
tion  lamp  on  the  Electric  parking  brake
switch go off.
 
Before driving, be sure that the parking brake
is released and the brake warning lamp is off.
When  parking  on  a  hill,  apply  the  parking
brake  and  turn  the  front  wheels  towards  the
kerb on a downhill grade, away from the kerb
on an uphill grade.

CAUTION

l

After  the  Electric  parking  brake  switch  has
been operated to apply or release the Electric
parking  brake,  if  the  brake  warning  lamp
(red) and the indication lamp on the Electric
parking brake switch remain blinking or the
Electric  parking  brake  warning  lamp  (yel-
low) remain illuminated, the Electric parking
brake system may be malfunctioning and the
parking  brake  may  not  be  applied  or  re-
leased.  Immediately  park  your  vehicle  in  a
safe  place  and  contact  the  nearest
MITSUBISHI  MOTORS  Authorized  Serv-
ice Point.

l

If  a  vehicle  is  driven  without  releasing  the
electric  parking  brake,  the  brake  will  over-
heat,  resulting  in  ineffective  braking  and
possible brake failure.

CAUTION

l

If the brake warning lamp (red) does not go
off after the parking brake has been released,
the brake system may be malfunctioning.
Contact the nearest MITSUBISHI MOTORS
Authorized Service Point.

l

If  the  acceleration  of  the  vehicle  seems  ab-
normally  slow  after  the  vehicle  has  been
parked  with  the  Electric  parking  brake  ap-
plied  in  cold  weather,  stop  the  vehicle  in  a
safe  place,  then  apply  and  release  the  Elec-
tric parking brake. If the vehicle acceleration
is 

still 

slow, 

contact 

the 

nearest

MITSUBISHI  MOTORS  Authorized  Serv-
ice Point.

NOTE

l

When  the  ignition  switch  or  the  operation
mode  is  other  than  ON,  the  parking  brake
cannot be released.

l

If  the  Electric  parking  brake  does  not  auto-
matically release, it may be released by man-
ual operation.

Parking brake

6-07

OGKE18E1

Starting and driving

6

Summary of Contents for ECLIPSE CROSS 2017



























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ECLIPSE CROSS 2017

Camcar 40000 Manual preview
40000
Brand: Camcar Pages: 6
Ford F-150 2018 Quick Reference Manual preview
F-150 2018
Brand: Ford Pages: 12
Kolpin Outdoors 25-1080 Assembly & Owners Manual preview
25-1080
Brand: Kolpin Outdoors Pages: 6
Schartec CR 4 Manual preview
CR 4
Brand: Schartec Pages: 2
Camoplast Polaris TATOU 4S Installation Manuallines preview
Polaris TATOU 4S
Brand: Camoplast Pages: 13
Dodge 2005 JR41 Stratus Owner'S Manual preview
2005 JR41 Stratus
Brand: Dodge Pages: 293
rough country 921107830 Installation Instruction preview
921107830
Brand: rough country Pages: 4
HAKR TRIP 3 Instructions For Use Manual preview
TRIP 3
Brand: HAKR Pages: 9
NavLinkz RL4-LR16-8 Manual preview
RL4-LR16-8
Brand: NavLinkz Pages: 26
Kuda 050130 Installation Instruction preview
050130
Brand: Kuda Pages: 4
Brink 4602 Fitting Instructions Manual preview
4602
Brand: Brink Pages: 12
Mercedes-Benz SLK 2014 Owner'S Manual preview
SLK 2014
Brand: Mercedes-Benz Pages: 357
Honda 2005 Civic Owner'S Manual preview
2005 Civic
Brand: Honda Pages: 234
Thule 202 Installation Instructions preview
202
Brand: Thule Pages: 1
GMC 2013 Terrain Owner'S Manual preview
2013 Terrain
Brand: GMC Pages: 364
FORM FIT HD 5M08 Installation Instructions Manual preview
HD 5M08
Brand: FORM FIT Pages: 6
Hotchkis 22101 Installation Manual preview
22101
Brand: Hotchkis Pages: 14
Outback S2 Quick Installation Manual preview
S2
Brand: Outback Pages: 2

Brands by name

Popular brands

Load more brands