Mitsubishi ECLIPSE CROSS 2017 Owner'S Manual Download Page 273 | Manualshive

Page: 273 / 538

background image

Rear Cross Traffic Alert
(RCTA)*

E00652400071

The  Rear  Cross  Traffic  Alert  (RCTA)  is  an
aid system for backing up. When the RCTA
system  detects  vehicles  approaching  from
sides  while  your  vehicle  is  reversing,  the
Blind  Spot  Warning  lamps  in  the  outside
rear-view mirrors on both sides will blink and
a  buzzer  will  sound  to  alert  the  driver.  A
warning  message  will  also  appear  on  the  in-
formation  screen  of  the  multi-information
display.

WARNING

l

Before using the RCTA, read this entire
section to fully understand the limitations
of this system. Failure to follow instruc-
tions could result in an accident.

WARNING

l

Never  rely  solely  on  the  RCTA  when
backing  up.  The  RCTA  is  an  aid  system.
It  is  not  a  substitute  for  your  safe  and
careful driving. Always check visually be-
hind and all around your vehicle for other
vehicles, persons, animals or obstructions.
The performance of the RCTA may vary
depending  on  driving,  traffic  and/or  sur-
rounding conditions.

NOTE

l

The  Blind  Spot  Warning  lamps  in  the  out-
side  rear-view  mirrors  on  both  sides  will
blink,  even  when  only  one  vehicle  is  ap-
proaching from one side.

Rear Cross Traffic Alert (RCTA)*

6-99

OGKE18E1

Starting and driving

6

«
...
271
272
273
274
275
...
»

Summary of Contents for ECLIPSE CROSS 2017



























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ECLIPSE CROSS 2017

Brand: Saab Pages: 75

Brand: Hama Pages: 6

Brand: JANE Pages: 21

2005 P207 Explorer Sport Trac

Brand: Ford Pages: 540

Brand: Metra Electronics Pages: 5

Brand: Renkforce Pages: 4

Parktronic system Volkswagen Golf MK7

Brand: Car-Systems Pages: 10

Turbocharger 15012

Brand: Edelbrock Pages: 1

Yukon XL Denali 2015

Brand: GMC Pages: 439

Brand: Hyundai Pages: 380

Brand: Kuda-Phonebase Pages: 3

Brand: Davis Instruments Pages: 16

$T-Rex TEX-51127 Installation Manual preview$

Brand: T-Rex Pages: 9

Brand: Chevrolet Pages: 426

STEALTH POWER RBP-215-SP

Brand: RBP Pages: 16

Brand: Stoneridge Pages: 34

Brand: Ultraflex Pages: 40

Brand: Gazer Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands