Mitsubishi ECLIPSE CROSS 2017 Owner'S Manual Download Page 407

Page: 407 / 538

To remove the spare wheel

E00803501770

1. Lift up the luggage floor board.

(Refer to “Luggage floor board” on page
7-90.)

2. To remove the spare wheel, remove the

installation clamp (A) by turning it anti-
clockwise.

NOTE

Put the spare wheel under the vehicle body
near the jack. This makes it safer if the jack
slips out of position.

To change a tyre

E00803202644

1. On vehicles with wheel covers, first re-

move the covers (refer to “ Wheel cov-
ers ” on page 8-19.

Then loosen the wheel nuts a quarter
turn with the wheel nut wrench. Do not
remove the wheel nuts yet.

2. Place the jack under one of the jacking

points (A) shown in the illustration. Use
the jacking point closest to the tyre you
wish to change.

How to change a tyre

8-15

OGKE18E1

For emergencies

Summary of Contents for ECLIPSE CROSS 2017



























































































































































































































































































































































































































































































































































Search results

Summary of Contents for ECLIPSE CROSS 2017

Reviews:

Related manuals for ECLIPSE CROSS 2017

Brands by name

Popular brands

Mitsubishi ECLIPSE CROSS 2017, Owner'S Manual

Search results

Summary of Contents for ECLIPSE CROSS 2017

Reviews:

Related manuals for ECLIPSE CROSS 2017

Brands by name

Popular brands