Mitsubishi ECLIPSE CROSS 2017 Owner'S Manual Download Page 153

Page: 153 / 538

Adjusting the brightness of the

display

When the display is open, push the side or

side of the switch to adjust the bright-

ness of the display. The brightness can be ad-
justed to 16 different levels.

Switching the navigation infor-

mation display

On vehicles equipped with MITSUBISHI
Multi- Communication System (MMCS), you
can select whether to display the navigation
information on the display.

1. To change the display setting, push the

switch when the display is open.

2. The setting top screen will be displayed,

push and hold the switch.

3. The display setting screen will be dis-

played.

Navigation information: ON

Navigation information: OFF

4. Push the side of the switch to select

“NAVI  INFORMATION  ON”  or  “NA-
VI  INFORMATION  OFF”,  and  then
push the   switch.

Head Up Display (HUD)*

5-53

OGKE18E1

Instruments and controls

Summary of Contents for ECLIPSE CROSS 2017



























































































































































































































































































































































































































































































































































Search results

Summary of Contents for ECLIPSE CROSS 2017

Reviews:

Related manuals for ECLIPSE CROSS 2017

Brands by name

Popular brands

Mitsubishi ECLIPSE CROSS 2017, Owner'S Manual

Search results

Summary of Contents for ECLIPSE CROSS 2017

Reviews:

Related manuals for ECLIPSE CROSS 2017

Brands by name

Popular brands