manualshive.com logo in svg

Mitsubishi ECLIPSE CROSS 2017, Owner'S Manual

The Mitsubishi ECLIPSE CROSS 2017 is a sleek and stylish crossover SUV that offers a comfortable and enjoyable driving experience. For those who own this vehicle, finding the Owner's Manual is essential. You can download the manual for free from manualshive.com to ensure you have all the information you need to maintain and operate your ECLIPSE CROSS.

Share
Download
background image

To operate

E00652300171

When  the  ignition  switch  is  turned  to  the
“ON” position or the operation mode is put in
ON and “ON” is selected in the “BSW” set-
ting  screen,  the  Blind  Spot  Warning  (BSW)
indication  lamp  in  the  instrument  cluster
comes  on  and  the  BSW  enters  the  standby
state.
When  “OFF”  is  selected  in  the  “BSW”  set-
ting  screen,  the  Blind  Spot  Warning  (BSW)
indication lamp in the instrument cluster goes
off and the BSW turns off.
To turn the BSW ON/OFF, follow the proce-
dure below.

1. Switch to the function setting screen.

Refer  to  “Multi-information  display
switches” on page 5-04
Refer  to  “Changing  the  function  set-
tings” on page 5-13

2. Press the   switch or   switch several

times to switch to the “BSW” screen.
Then, press the   switch to switch to en-
ter the setting selection screen.

3. Press the   switch or   switch to select

the  “ON”  or  “OFF”,  and  then  press  the

 switch to confirm the setting.

Indication lamp

If you turn the BSW ON/OFF, the Rear Cross
Traffic  Alert  (RCTA)  also  turns  ON/OFF  at
the same time.

NOTE

l

When  the  ignition  switch  is  turned  to  the
“LOCK”  position  or  the  operation  mode  is
set to OFF, the selected condition just before
setting to OFF is retained.

l

The BSW operates when all of the following
conditions are met.

•

The ignition switch is turned to the “ON”
position  or  the  operation  mode  is  put  in
ON.

•

The  selector  lever  is  in  positions  other
than “P” (Park) and “R” (Reverse).

NOTE

•

The speed of your vehicle is approximate-
ly 10 km/h (6 mph) or higher.

When the sensor detects an ap-

proaching vehicle

When the Blind Spot Warning (BSW) indica-
tion lamp in the instrument cluster is on, if a
vehicle is approaching your vehicle in the de-
tection area, the Blind Spot Warning lamp in
the outside rear-view mirror illuminates.
If the turn-signal lever is operated to the side
where the Blind Spot Warning lamp is illumi-
nated,  the  Blind  Spot  Warning  lamp  will
blink and the system will beep three times to
alert the driver.

Blind Spot Warning (BSW) (with Lane Change Assist)*

6-97

OGKE18E1

Starting and driving

6

Summary of Contents for ECLIPSE CROSS 2017



























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ECLIPSE CROSS 2017

Toyota 2012 Rav4 Owner'S Manual preview
2012 Rav4
Brand: Toyota Pages: 529
Wagan 2591 User Manual preview
2591
Brand: Wagan Pages: 12
Kargo Master 80070 Assembly Lnstructions preview
80070
Brand: Kargo Master Pages: 13
Kargo Master 4A96L Installation Manual preview
4A96L
Brand: Kargo Master Pages: 21
Kargo Master 40201 Installation Manual preview
40201
Brand: Kargo Master Pages: 4
Tesla V2 SUPERCHARGER First Responder'S Manual preview
V2 SUPERCHARGER
Brand: Tesla Pages: 9
Genesis Multiple G9F18 AU000 Quick Start Manual preview
Multiple G9F18 AU000
Brand: Genesis Pages: 3
SuperATV AAB-P-RZR900-K2-001 Installation Instructions preview
AAB-P-RZR900-K2-001
Brand: SuperATV Pages: 3
muth signal mirror 2005-2009 Ford Mustang Installation Instruction preview
signal mirror 2005-2009 Ford Mustang
Brand: muth Pages: 9
AA Products SR-A260 Instruction Manual preview
SR-A260
Brand: AA Products Pages: 4
TATA Motors TIGOR EV 2021 Owner'S Manual preview
TIGOR EV 2021
Brand: TATA Motors Pages: 236
POOL-LINE 110085 Assembly Instructions preview
110085
Brand: POOL-LINE Pages: 2
Cadillac XLR-V Specifications preview
XLR-V
Brand: Cadillac Pages: 2
Buick Cascada 2016 Getting To Know Manual preview
Cascada 2016
Brand: Buick Pages: 20
Edelbrock 29135 Installation Instructions preview
29135
Brand: Edelbrock Pages: 2
Mercedes-Benz 1989 560 SL Owner'S Manual preview
1989 560 SL
Brand: Mercedes-Benz Pages: 93
Whispbar K481W Fitting Instructions Manual preview
K481W
Brand: Whispbar Pages: 14
TOGU Airgo Active cushion / Comfort Manual And Maintenance Instructions preview
Airgo Active cushion / Comfort
Brand: TOGU Pages: 2

Brands by name

Popular brands

Load more brands