manualshive.com logo in svg

Mitsubishi ECLIPSE CROSS 2017, Owner'S Manual

The Mitsubishi ECLIPSE CROSS 2017 is a sleek and stylish crossover SUV that offers a comfortable and enjoyable driving experience. For those who own this vehicle, finding the Owner's Manual is essential. You can download the manual for free from manualshive.com to ensure you have all the information you need to maintain and operate your ECLIPSE CROSS.

Share
Download
background image

Filling the fuel tank

E00200204494

WARNING

l

When handling fuel, comply with the safe-
ty  regulations  displayed  by  garages  and
filling stations.

l

Gasoline  is  highly  flammable  and  explo-
sive. You could be burned or seriously in-
jured  when  handling  it.  When  refueling
your  vehicle,  always  turn  the  engine  off
and  keep  away  from  flames,  sparks,  and
smoking materials. Always handle fuel in
well-ventilated outdoor areas.

l

Before  removing  the  fuel  cap,  be  sure  to
get rid of your body’s static electricity by
touching  a  metal  part  of  the  vehicle  or
fuel  pump.  Any  static  electricity  on  your
body could create a spark that ignites fuel
vapour.

l

Perform  the  whole  refueling  process
(opening the fuel tank filler door, remov-
ing the fuel cap, etc.) by yourself. Do not
let  any  other  person  come  near  the  fuel
tank filler. If you allowed a person to help
you  and  that  person  was  carrying  static
electricity, fuel vapour could be ignited.

l

Do not move away from the fuel tank fill-
er until refueling is finished. If you moved
away  and  did  something  else  (for  exam-
ple,  sitting  on  a  seat)  part-way  through
the refueling process, you could pick up a
fresh charge of static electricity.

WARNING

l

If the tank cap must be replaced, use only
a MITSUBISHI MOTORS genuine part.

Fuel tank capacity

2WD models: 63 litres
4WD models: 60 litres

Refueling

1. Before filling with fuel, stop the engine.
2. The fuel tank filler is located on the rear

left side of your vehicle.
Open the fuel tank filler door by pulling
the  release  lever  located  on  the  side  of
the driver’s seat.

3. Open the fuel tank filler tube by slowly

turning the cap anticlockwise.

1- Remove
2- Close

CAUTION

l

Since the fuel system may be under pressure,
remove  the  fuel  tank  filler  tube  cap  slowly.
This  relieves  any  pressure  or  vacuum  that
might  have  built  up  in  the  fuel  tank.  If  you
hear  a  hissing  sound,  wait  until  it  stops  be-
fore removing the cap. Otherwise, fuel may
spray out, injuring you or others.

Filling the fuel tank

2-03

OGKE18E1

General information

2

Summary of Contents for ECLIPSE CROSS 2017



























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ECLIPSE CROSS 2017

Lancia THESIS CONNECT Owner'S Handbook Manual preview
THESIS CONNECT
Brand: Lancia Pages: 386
Lange Originals HOIST-A-TOP JL CRANK Installation Instructions Manual preview
HOIST-A-TOP JL CRANK
Brand: Lange Originals Pages: 13
RaceChip XLR User Manual preview
XLR
Brand: RaceChip Pages: 20
Volvo 2004 V70 (Swedish) Användarmanual preview
2004 V70
Brand: Volvo Pages: 188
Xblitz Mirror 2016 User Manual preview
Mirror 2016
Brand: Xblitz Pages: 30
Opel 2013 Corsa Brochure & Specs preview
2013 Corsa
Brand: Opel Pages: 32
Saab 9000 1985 Service Manual preview
9000 1985
Brand: Saab Pages: 92
A-rival PNC70 Active Hardware Manual preview
PNC70 Active
Brand: A-rival Pages: 23
Cadillac 2011 SRX CROSSOVER Owner'S Manual preview
2011 SRX CROSSOVER
Brand: Cadillac Pages: 416
TIE DOWN LONGRUN 86103 Assembly/Installation Instructions preview
LONGRUN 86103
Brand: TIE DOWN Pages: 2
Mitsubishi Fuso FK 2010 Owner'S Manual preview
Fuso FK 2010
Brand: Mitsubishi Pages: 362
Xingyun XY40EV Service Manual preview
XY40EV
Brand: Xingyun Pages: 74
Edelbrock 460 Ford Installation Instructions preview
460 Ford
Brand: Edelbrock Pages: 2
Xpresskit PKTX Installation Manual preview
PKTX
Brand: Xpresskit Pages: 12
Edelbrock Performer-Plus 2172 Installation Instructions preview
Performer-Plus 2172
Brand: Edelbrock Pages: 4
Reliant ROBIN 850 Workshop Manual preview
ROBIN 850
Brand: Reliant Pages: 206
Mitsubishi MOTORS OUTLANDER PHEV 2022 Manual preview
OUTLANDER PHEV 2022
Brand: Mitsubishi MOTORS Pages: 8
iQOS CCU01 Safety Warnings And Instructions preview
CCU01
Brand: iQOS Pages: 4

Brands by name

Popular brands

Load more brands