manualshive.com logo in svg

Microsemi SyncServer S600, User Manual

Share
Download
Microsemi SyncServer S600 User Manual Download Page 190

190

SyncServer 600 Series User’s Guide

098-00720-000 Revision B – April, 2016

Appendix A  System Messages
System Notification Messages

Ethernet Port3 Port 
link down

117

Minor

No

LAN3 port link down

LAN3 port link down 
cleared

Check cable. 

Check the box the 
interface is 
connected to. 

Check 
Auto-negotiation.

No action required

Ethernet Port4 Port 
link down

118

Minor

No

LAN4 port link down

LAN4 port link down 
cleared

Check cable. 

Check the box the 
interface is 
connected to. 

Check 
Auto-negotiation.

No action required

RESERVED

119

RESERVED

120

Operational Failure:

132

Major

No

Operational failure: 1PPS 
interrupt. GNSS upgrade 
failure after the 1PPS 
interrupt.

Operational failure 
cleared

If alarm persists 
power cycle/reboot

Call SGS support if it 
persists after 
reboot/power cycle.

No action required

Power Out of Range

131

Major

No

[ +13.2 | +5 | OSC 
+% | +3.3 | +2.5 | 
+1.5 | +1.1 | +1.0]

out of range 

____ out of range cleared

If alarm persists 
power cycle/reboot

Call SGS support if it 
persists after 
reboot/power cycle.

n/a

Table A-1.  System Notification Messages (Continued)

Description

Event 

ID

Msg

Level

Trans-

itory

MsgText

Corrective Action

Summary of Contents for SyncServer S600





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands