Microsemi SyncServer S600 User Manual Download Page 105 | Manualshive

Page: 105 / 252

background image

098-00720-000 Revision B – April, 2016

SyncServer 600 Series User’s Guide

105

Chapter 4

Navigation Windows

The authentication file is provided with the upgrade file and verifies that this
SyncServer unit is authorized to upgrade with the specified upgrade file.

Note:

For releases after 1.1, if the upgrade process is used to load a

previous (older) version of the software, then the unit will reset the
configuration to factory default values.

Note:

If the all-packets limit on LAN1 has been reduced on the

Security->Packet Monitoring page, then it is recommended that the
limit be temporarily increased back to the default value of 13000
packets/second. Otherwise, the file upload will be very slow and may
timeout.

«
...
103
104
105
106
107
...
»

Summary of Contents for SyncServer S600





























































































































































































































































Reviews:

No comments

Related manuals for SyncServer S600

Brand: Xerox Pages: 220

Brand: Xerox Pages: 28

DocuPrint 100MX

Brand: Xerox Pages: 2

Brand: NEC Pages: 151

Brand: Omega Pages: 49

Brand: Iwatsu Pages: 338

Brand: TYAN Pages: 64

TJA670 domovea Basic

Brand: hager Pages: 36

Brand: KYLAND Pages: 30

Brand: Flexport Pages: 39

Vlinx VESR4 4 Series

Brand: B&B Electronics Pages: 70

88743BU - System x3950 E

Brand: IBM Pages: 426

Brand: Icy Box Pages: 3

Brand: HP Pages: 94

Integrity rx5670

Brand: HP Pages: 46

Brand: HP Pages: 98

NetServer AA 4000

Brand: HP Pages: 82

Brand: HP Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands