Megger BITE 2 Instruction Manual Download Page 9

Page: 9 / 135

INTRODUCTION

AVTM246004 BITE 2/2P Rev 4 July 2011

Applications for the BITE 2/2P

The BITE 2/2P measures the following battery types, ranging
to 7000 Ah:

•

lead-acid flooded cells

•

sealed (VRLA) cells

•

nickel-cadmium cells

The BITE 2/2P tests many system types, including:

•

telecommunications

•

substations

•

UPS systems

•

electrical power substations

•

railroad signals and communications

•

motive power batteries

•

aircraft power supplies

•

marine and military applications

•

many others

For information about other installations that might benefit
from impedance testing, contact Megger.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for BITE 2








































































































































Search results

Summary of Contents for BITE 2

Reviews:

Related manuals for BITE 2

Brands by name

Popular brands

Megger BITE 2, Instruction Manual

Search results

Summary of Contents for BITE 2

Reviews:

Related manuals for BITE 2

Brands by name

Popular brands