manualshive.com logo in svg

Megger BITE 2, Instruction Manual

The Megger BITE 2 is a powerful battery impedance tester used for testing the integrity of battery systems. Ensure peak performance with the Instruction Manual available for free download from manualshive.com. This comprehensive manual provides detailed guidance on operating and troubleshooting your Megger BITE 2.

Share
Download
background image

M 

 
 

AVTM246004  BITE 2/2P  Rev 4 July 2011 

107 

 

I

CONTENTS 

INTRODUCTION............................................................................................................................................................... 109 

About AVOLINK….............................................................................................................................................. 109 
System Requirements for PC ................................................................................................................................ 110 

INSTALLATION ................................................................................................................................................................. 111 
Using Avolink with the BITE.............................................................................................................................................. 119 

Connecting the BITE to the PC........................................................................................................................... 119 
Starting AVOLINK................................................................................................................................................ 119 
The AVOLINK Window .......................................................................................................................................120 

Transferring the BITE Test Data........................................................................................................................................ 121 

Prepare the PC For Data Transfer........................................................................................................................123 
Transfer Data............................................................................................................................................................124 
Disconnect the BITE from the PC.......................................................................................................................127 
Viewing and Printing Test Data ........................................................................................................................... 128 

Communications Functions ................................................................................................................................................. 131 

Setup Serial Port...................................................................................................................................................... 132 
Test Communications ............................................................................................................................................ 135 
Printer Setup............................................................................................................................................................ 136 
AVOCOM 32.......................................................................................................................................................... 136 

 

 

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for BITE 2








































































































































Reviews:

No comments

Related manuals for BITE 2

lancer 9000 series Installation Manual preview
9000 series
Brand: lancer Pages: 12
idiag P100 Manual preview
P100
Brand: idiag Pages: 10
Bandit 2290 Operating & Parts Manual preview
2290
Brand: Bandit Pages: 136
3M Versaflo S Series User Instructions preview
Versaflo S Series
Brand: 3M Pages: 11
3M DBI Sala EXOFIT User Instructions preview
DBI Sala EXOFIT
Brand: 3M Pages: 32
3M 746 Instructions Manual preview
746
Brand: 3M Pages: 8
Accurate Bio-Medical Technology WS Series User Manual preview
WS Series
Brand: Accurate Bio-Medical Technology Pages: 35
Tate Grid User Installation preview
Grid
Brand: Tate Pages: 7
Tate Grid User'S Installation Manual preview
Grid
Brand: Tate Pages: 5
Calivita BioHarmonex BH4 Product Information & User Manual preview
BioHarmonex BH4
Brand: Calivita Pages: 38
CAIRE FreeStyle Manual preview
FreeStyle
Brand: CAIRE Pages: 91
Faderfox DL3 User Manual preview
DL3
Brand: Faderfox Pages: 8
Hammer Strength MTSP Unpacking And Assembly Instructions preview
MTSP
Brand: Hammer Strength Pages: 18
Mangar International Leglifter User Instructions And Warranty preview
Leglifter
Brand: Mangar International Pages: 8
Malvern Instruments Zetasizer uV Manual preview
Zetasizer uV
Brand: Malvern Instruments Pages: 30
zarges Z200 Assembly And Usage Instructions preview
Z200
Brand: zarges Pages: 36
Sagola 4240 Instruction Manual preview
4240
Brand: Sagola Pages: 62
Qu-Bit Electronix RT60 User Manual preview
RT60
Brand: Qu-Bit Electronix Pages: 15

Brands by name

Popular brands

Load more brands