Megger BITE 2 Instruction Manual Download Page 77

Page: 77 / 135

AVTM246004 BITE 2/2P Rev 4 July 2011

Carefully remove the probe housing. Remove the back
cover.

CAUTION

Do not disturb the wrist strap, trigger assembly, or wiring
harness.

Locate the battery pack at the base of the

receiver

Unplug the battery pack from the 5-PIN connector of the

receiver

printed circuit board

Dispose of the Ni-Cd battery
pack in an environmentally safe
way.

Install the replacement battery pack (part number 30654).

Be sure to align the replacement battery pack connector
with the keyed mating connector on the printed circuit
board.

Reassemble the

receiver

by placing the back cover over

the printed circuit board.Ensure that the two connector-
mounting plates are aligned with the channels inside the
back cover.

Snap the back cover into place, and then fasten it using
the six Phillips head screws.

Snap the probe housing into place, and then fasten it
using the two Phillips head screws.

WARNING

Make sure that no wires are pinched when replacing
covers and housings!!!!!

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for BITE 2








































































































































Search results

Summary of Contents for BITE 2

Reviews:

Related manuals for BITE 2

Brands by name

Popular brands

Megger BITE 2, Instruction Manual

Search results

Summary of Contents for BITE 2

Reviews:

Related manuals for BITE 2

Brands by name

Popular brands