Megger BITE 2 Instruction Manual Download Page 52

Page: 52 / 135

AVTM246004 BITE 2/2P Rev 4 July 2011

From transmitter
(current source
leads)

Figure 5-1: Reversing the current source leads on a single string of cells

when a high or low current message is displayed.

Verifying the Source Current

A low current indication on the

transmitter’s

analog or

digital meter can be caused by high resistance in the cell
string. To verify whether the magnitude of the source current
is within the required limits (3-15 A):

This temporarily “disconnects”
the transmitter and blocks the
current from going to the
battery.

Press the Current switch on the BITE 2/2P

transmitter

to the

(

(OFF) position.

Disconnect the

current source leads

from the battery.

Connect the

current source lead

clips together and

restart current flow by pressing the BITE 2/2P

transmitter

Current On/Off switch to the



(ON) position.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for BITE 2








































































































































Search results

Summary of Contents for BITE 2

Reviews:

Related manuals for BITE 2

Brands by name

Popular brands

Megger BITE 2, Instruction Manual

Search results

Summary of Contents for BITE 2

Reviews:

Related manuals for BITE 2

Brands by name

Popular brands