manualshive.com logo in svg

Megger BITE 2, Instruction Manual, Page: 32 / 135

Share
Download
Megger BITE 2 Instruction Manual Download Page 32

M 

 

 

AVTM246004  BITE 2/2P  Rev 4 July 2011 

28 

Step Two: Powering-on the Receiver 

 

After you successfully perform the pretest activities described 
Step One, you are ready to power on the 

receiver

.

 

 

POWER ON 
Switch

 

ENTER Key 

7-Pin 
Connector 

4-Pin 
Connector 

Potential 
Probe

 

3-Pin 
Connector 

LCD

 

TRIGGER

 

UP and 
DOWN 
ARROW 
Keys 

 

Figure 4-1:  Receiver controls, connectors and indicators 

 

1. 

Make sure the 

receiver

 charger is disconnected from the 

receiver.

 

 

NOTE:

 Do not use the 

receiver

 to perform tests while the 

charger is connected to the receiver. 

 

2. 

Connect the 

potential probe

 

cable assembly

 to the 7-pin 

connector on the 

receiver

.

 

 

3. 

Press the POWER ON switch on the 

receiver

. 

 

The 

receiver

 powers on and displays several initialization 

screens.  

 

 

 

 

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for BITE 2








































































































































Reviews:

No comments