background image

215585

104

Revision A

$

%

&

Figure 5.10: Allowable Driveline Length

6.

Check distance (C) between tractor primary power take-off
(PTO) shaft (A) and rotary disc pull-type hitch gearbox
shaft (B) without the front half of the driveline attached.

7.

Ensure that distance (C) does

NOT

exceed the dimensions

listed in Table

5.2, page 104

.

Table 5.2 Distance between Hitch Gearbox and Tractor PTO

Driveline Shaft Size

Distance (C)

1

34 mm (1 3/8 in.)

650 mm (25 9/16 in.)

43 mm (1 3/4 in.)

750 mm (29 1/2 in.)

$

Figure 5.11: Driveline Attached to Tractor PTO

8.

Position primary driveline (A) onto the tractor

s PTO shaft,

making sure that the driveline is approximately level.

9.

Pull back the collar on driveline (A) and push the driveline
until it locks. Release the collar.

CAUTION

Check to be sure all bystanders have cleared the area.

$

%

Figure 5.12: Hitch Stand in Working Position

10. Clear bystanders from the area and start the tractor. Do

NOT

operate the rotary disc pull-type.

11. Raise the hitch so that stand (A) is off the ground.

12. Shut down the engine, and remove the key from

the ignition.

13. Remove inner hairpin (B) to release stand (A).

CONNECTING THE TRACTOR TO THE ROTARY DISC PULL-TYPE

1.

If distance (C) is greater than the values shown, a longer driveline is required. Refer to the rotary disc pull-type
operator

s manual, options and attachments section for ordering information.

Summary of Contents for R113





















































































































































































































Reviews: