MacDon M 2009 Series, Assembly Instructions Manual

Page: 99 / 117

UNLOADING AND ASSEMBLY
Form 169242 Revision F
99
L1 C x x x || S E N S O R I N P U T
L2 M x x x || H D R H E I G H T S E N S O R
L1 C x x x || S E N S O R I N P U T
L2 M x x x || H E A D E R A N G L E S E N S O R
L1 C x x x || S E N S O R I N P U T
L2 M x x x || K N I F E S P E E D S E N S O R
L1 C x x x || S E N S O R I N P U T
L2 M x x x || R E E L S P E E D S E N S O R
L1 C x x x || A C T I V A T E F U N C T I O N S ?
L2 M x x x || N O / Y E S E X I T D I A G N O S T I C S ?
L1 C x x x || A C T I V A T E F U N C T I O N S ?
L2 M x x x || H E A D E R D O W N / U P
L1 C x x x || A C T I V A T E F U N C T I O N S ?
L2 M x x x || R E E L D O W N / U P
L1 C x x x || A C T I V A T E F U N C T I O N S ?
L2 M x x x || H D R T I L T I N / O U T
L1 C x x x || A C T I V A T E F U N C T I O N S ?
L2 M x x x || K N I F E D R I V E O N
L1 C x x x || A C T I V A T E F U N C T I O N S ?
L2 M x x x || D R A P E R / A U G E R O N
L1 C x x x || A C T I V A T E F U N C T I O N S ?
L2 M x x x || R E E L F O R E / A F T
L1 C x x x || A C T I V A T E H Y D P U R G E ?
L2 M x x x || N O / Y E S
L1 C x x x || T O A C T I V A T E P U R G E
L2 M x x x || P R E S S A N D H O L D
L1 C x x x || P U R G E C Y C L E S T A R T E D
L2 M x x x || P R E S S A N D H O L D
L1 C x x x || P U R G E C Y C L E E N D E D
L2 M x x x ||
L1 C x x x || P U R G E C Y C L E E N D E D
L2 M x x x || N O E X I T Y E S
L1 C x x x || E X I T F U N C T I O N M E N U ?
L2 M x x x || N O / Y E S H E A D E R D O W N / U P
L1 C x x x || E X I T D I A G N O S T I C S ?
L2 M x x x || N O / Y E S D I A G N O S T I C M O D E ?
If "NO" then jump to:
If "NO" then jump to:
ACTIVATE HYD PURGE - This is to allow the operator
to purge the air from a new or changed pump system.
Pressing and holding the right hand "arrow" button
activates a predetermined timed purge cycle.
Releasing pressure on the switch or a completed cycle
(timed out) will jump to the PURGE CYCLE ENDED
menu selection.
If the HEADER TILT cylinder or the REEL FORE / AFT
valve is not installed under the TRACTOR SETUP
menu then the ACTIVATE FUNCTIONS menu selection
for these items should be suppressed.
If no expansion module or an A30 auger header is
selected, the corresponding menu items should be
suppressed.
For diagnostic purposes each header function can be
activated by using the "arrow" keys on the CDM. When
"SELECT" is pressed the program will go to the next
function that can be activated.
If "NO" then jump to:
If a sensor has been disabled "SENSOR" will be
flashing in the area where the input reading would
have been.