MacDon M 2009 Series, Assembly Instructions Manual

Page: 95 / 117

UNLOADING AND ASSEMBLY
Form 169242 Revision F
95
B. M105 DETAILED PROGRAMMING INSTRUCTIONS
(Ignition ON / Engine Running or Not / Header Disengaged).
(Press
PROGRAM
and
SELECT
on CDM to enter programming mode).
(If necessary, refer to the M Series Windrower Operator’s Manual for programming to specific crop types and conditions).
(continued next page)
L1 C x x x
||
T R A C T O R S E T U P ?
L2 M x x x
||
N O / Y E S C A B D I S P L A Y S E T U P ?
L1 C x x x || S E L E C T H E A D E R T Y P E ?
L2 M x x x || D R A P E R
L1 C x x x || S E L E C T H E A D E R T Y P E ?
L2 M x x x || A 3 0 A U G E R
L1 C x x x || S E L E C T H E A D E R T Y P E ?
L2 M x x x || A 4 0 A U G E R
L1 C x x x || T I L T C Y L I N S T A L L E D ?
L2 M x x x || N O / Y E S
L1 C x x x || R E E L F O R E / A F T ?
L2 M x x x || N O / Y E S
L1 C x x x || K N I F E O V E R L O A D S P D ?
L2 M x x x || 1 0 0 0 S P M
L1 C x x x || H E A D E R I N D E X M O D E ?
L2 M x x x || R E E L & C O N V E Y O R
L2 M x x x || R E E L O N L Y
L1 C x x x || R E T U R N T O C U T M O D E ?
L2 M x x x || H E I G H T & T I L T
L2 M x x x || H E I G H T O N L Y
L1 C x x x || H E A D E R C U T W I D T H ?
L2 M x x x || 2 0 . 5 F E E T
L1 C x x x || H A Y C O N D I T I O N E R ?
L2 M x x x || N O / Y E S
L1 C x x x || A U G E R H D R R E E L S P D
L2 M x x x || R P M / M P H
L2 M x x x || R P M / K P H
L1 C x x x || S E T T I R E S I Z E ?
L2 M x x x || 1 8 . 4 X 2 6 T U R F
L2 M x x x || 1 8 . 4 X 2 6 B A R
L2 M x x x || 2 3 . 1 X 2 6 T U R F
L2 M x x x || 6 0 0 - 6 5 R 2 8
L1 C x x x || S E T E N G I N E I S C R P M ?
L2 M x x x || O F F / O N S E T C O N T R O L L O C K S ?
L1 C x x x || S E T C O N T R O L L O C K S ?
L2 M x x x || N O / Y E S V I E W C O N T R O L L O C K S ?
Programming Menu Flow Chart
If "NO" then jump to:
Use the "arrow" keys to set the header cut width.
If the REEL SPEED sensor is not "installed" (A30
Auger Header selected) in the TRACTOR SETUP
menu, the INDEX mode should be suppressed.
If the HEADER TILT sensor is not "installed" (no
expansion module installed), then the RTC mode
should default to HEIGHT only.
Selects the header type, the selected header will be
flashing. The "factory" default to be DRAPER.
If the A30 is selected them the reel speed should be
suppressed as there is no reel speed sensor.
AUGER HEADER ONLY
For IMPERIAL display.
For METRIC display.
If a DRAPER or A40 is selected the reel speed should
be enabled (with expansion module installed).
Knife Overload Speed should be suppressed unless
the expansion module is installed.
The TILT selection meeds to be available even if the
expansion module is not installed.
DRAPER HEADER ONLY. Default will be flashing.
Use "arrow" keys to select.
If "NO" then jump to:
Pressing "SELECT" will jump to:
Pressing "SELECT" will go to the next line 1 (L1)
menu selection. The turn signal "arrow" keys are used
to change the values.