MacDon M 2009 Series, Assembly Instructions Manual

Page: 96 / 117

UNLOADING AND ASSEMBLY
Form 169242 Revision F
96
(continued next page)
L1 C x x x || D R A P E R S P E E D
L2 M x x x || E N A B L E D / L O C K E D
L1 C x x x || A U G E R S P E E D
L2 M x x x || E N A B L E D / L O C K E D
L1 C x x x || R E E L S P E E D
L2 M x x x || E N A B L E D / L O C K E D
L1 C x x x || R E E L F O R E / A F T
L2 M x x x || E N A B L E D / L O C K E D
L1 C x x x || H E A D E R T I L T
L2 M x x x || E N A B L E D / L O C K E D
L1 C x x x || E X I T C O N T R O L L O C K S ?
L2 M x x x || N O / Y E S D R A P E R S P E E D
E N A B L E D / L O C K E D
L1 C x x x || V I E W C O N T R O L L O C K S ?
L2 M x x x || N O / Y E S E X I T T R A C T O R S E T U P ?
L1 C x x x || D R A P E R S P E E D
L2 M x x x || 5 7 5 . 1 H R S E N A B L E D
L2 M x x x || 6 4 8 . 6 H R S L O C K E D
L1 C x x x || A U G E R S P E E D
L2 M x x x || 5 7 5 . 1 H R S E N A B L E D
L2 M x x x || 6 4 8 . 6 H R S L O C K E D
L1 C x x x || R E E L S P E E D
L2 M x x x || 5 7 5 . 1 H R S E N A B L E D
L2 M x x x || 6 4 8 . 6 H R S L O C K E D
L1 C x x x || R E E L F O R E / A F T
L2 M x x x || 5 7 5 . 1 H R S E N A B L E D
L2 M x x x || 6 4 8 . 6 H R S L O C K E D
L1 C x x x || H E A D E R T I L T
L2 M x x x || 5 7 5 . 1 H R S E N A B L E D
L2 M x x x || 6 4 8 . 6 H R S L O C K E D
L1 C x x x || E X I T V I E W L O C K O U T S ?
L2 M x x x || N O / Y E S D R A P E R S P E E D
L1 C x x x || E X I T T R A C T O R S E T U P ?
L2 M x x x || N O / Y E S T I L T C Y L I N S T A L L E D ?
L1 C x x x
||
C A B D I S P L A Y S E T U P ?
L2 M x x x
||
N O / Y E S C A L I B R A T E S E N S O R S ?
L1 C x x x || D I S P L A Y L A N G U A G E ?
L2 M x x x || E N G L I S H
L2 M x x x || E S P A N O L
L2 M x x x || R U S S I A N
L1 C x x x || D I S P L A Y U N I T S ?
L2 M x x x || I M P E R I A L
L2 M x x x || M E T R I C
The "arrow" keys are used to select between
IMPERIAL or METRIC. The default value will be
displayed first.
This menu allows the operator to selectably "lock out"
the control functions for the various header functions.
The default or selected "status" for each item will flash.
When the control lock outs are viewed, the lower
display line (L2) will show the engine hours and either
ENABLED or LOCKED to indicate the present status
along with the engine hours at which time the function
was either ENABLED or LOCKED.
If the expansion module is not installed the
corresponding menu items should be suppressed.
The "arrow" keys are used to ENABLE or LOCK OUT
each function. Pressing "SELECT" will go to the next
L1 menu item.
If "NO" then jump to:
If "NO" then jump to:
Using the "arrow" keys allows the operator to select the
various functions. Pressing "SELECT" will go to the
EXIT VIEW LOCKOUTS? menu selection.
If "NO" then jump to:
If "NO" then jump to:
Tilt to be suppressed if not "installed" in the tractor
setup menu.
If any of the HDR ANGLE / KNIFE SPEED or REEL
SPEED sensors are not "installed" (no expansion
module or A30 Auger header selected, they should be
suppressed.
If "NO" then jump to:
Use the "arrow" keys to change the default language.
Pressing "SELECT" goes to the next L1 menu
selection.