MacDon M 2009 Series, Assembly Instructions Manual

Page: 97 / 117

UNLOADING AND ASSEMBLY
Form 169242 Revision F
97
IMPORTANT: ENGINE MUST BE RUNNING TO CALIBRATE SENSORS
(continued next page)
L1 C x x x || C D M B U Z Z E R V O L U M E
L2 M x x x ||
▂ ▂ ▃ ▅ ▆ ▇
L1 C x x x || C D M B A C K L I G H T I N G
L2 M x x x ||
▂ ▂ ▃ ▅ ▆ ▇
L1 C x x x || C D M C O N T R A S T
L2 M x x x ||
▂ ▂ ▃ ▅ ▆ ▇
L1 C x x x || E X I T D I S P L A Y S E T U P ?
L2 M x x x || N O / Y E S D I S P L A Y L A N G U A G E ?
L1 C x x x
||
C A L I B R A T E S E N S O R S ?
L2 M x x x || N O / Y E S D I A G N O S T I C M O D E ?
L1 C x x x || T O C A L I B R A T E
S E L E C T
L2 M x x x || H E A D E R H E I G H T
L2 M x x x || H E A D E R T I L T
L2 M x x x || S T O P & E X I T
L1 C x x x || H E I G H T S E N S O R C A L
L2 M x x x || R A I S E H D R T O S T A R T
L1 C x x x || C A L I B R A T I N G H E I G H T
L2 M x x x || R A I S E H E A D E R H O L D
L2 M x x x || R A I S E H E A D E R D O N E
L1 C x x x || H E I G H T S E N S O R C A L
L2 M x x x || P R E S S L O W E R H E A D E R
L1 M x x x || C A L I B R A T I N G H E I G H T
L2 M x x x || L O W E R H E A D E R H O L D
L2 M x x x || H T S E N S O R C O M P L E T E
L1 C x x x || T O C A L I B R A T E S E L E C T
L2 M x x x || H E A D E R H E I G H T
L1 C x x x || T O C A L I B R A T E S E L E C T
L2 M x x x || H E A D E R H E I G H T
L2 M x x x || H E A D E R T I L T
L1 M x x x || H D R T I L T S E N S O R C A L
L2 M x x x || E X T E N D T L T T O S T A R T
L1 C x x x || C A L I B R A T I N G T I L T
L2 M x x x || E X T E N D T I L T H O L D
L2 M x x x || E X T E N D T I L T D O N E
L1 M x x x || H D R T I L T S E N S O R C A L
L2 M x x x || P R E S S R E T R A C T T I L T
L1 C x x x || C A L I B R A T I N G T I L T
L2 M x x x || R E T R A C T T I L T H O L D
L2 M x x x || H D R T I L T C O M P L E T E
L1 C x x x || T O C A L I B R A T E S E L E C T
L2 M x x x || H E A D E R T I L T
L2 M x x x || S T O P & E X I T
L1 C x x x || E X I T C A L I B R A T I O N ?
L2 M x x x || N O / Y E S T O C A L I B R A T E S E L E C T
If the HEADER TILT option in the TRACTOR SETUP
is set to NO then only HEIGHT should be available as
a menu selection for calibration.
The operator can select any of the two items requiring
calibration or to STOP & EXIT the menu.
If "NO" then jump to:
The "arrow" keys are used to change the CDM buzzer
volume, CDM backlighting or the CDM contrast, with
the bar graph indicating the relative level for each
item. When "SELECT" is pressed the program goes to
the EXIT DISPLAY SETUP? menu selection.
The menu will display the last item selected when the
calibration routine is completed.
When a function is activated, the display will indicate
the function being calibrated. HOLD will flash until the
system has completed reading in the signal with the
header fully raised.
If "NO" then jump to:
If "NO" then jump to:
DONE will flash and prompt the operator to
COMPLETE the sensor calibration by lowering the
header.