background image

13

206-4218

Rack Installation (Cont.)

Rack-mount Considerations

A. Elevated Operating Ambient

 

If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack 

environment may be greater than room ambient. Therefore, consideration should be given to 

installing the equipment in an environment compatible with the maximum ambient temperature 

(Tma) specified by the manufacturer (see Specifications information in this document).

B. Reduced Air Flow

 

Installation of the equipment in a rack should be such that the amount of air flow required for 

safe operation of the equipment is not compromised. To ventilate the system normally and 

avoid overheating, leave at least 1 inch (2.5 cm) on each side (including top and bottom) of 

the OAT100R. Do NOT stack other equipment on the top of the OAT100R. Also, if multiple 

OAT100R units are to be installed in close proximity, for example, in one rack, ensure that the 

units’ AC power adapters are never stacked or bundled. Each adapter should have adequate 

ventilation and should be isolated from other heat sources.

C. Circuit Overloading

  Consideration should be given to the connection of the equipment to the supply circuit and the 

effect that overloading of the circuits might have on overcurrent protection and supply wiring.

D. Reliable Earthing

  Maintain reliable earthing of rack-mounted equipment. Particular attention should be given to 

supply connections other than direct connections to the branch circuit (e.g., use of power strips). 

E. Mains Outlet Earthing

  The apparatus with Class I construction must be connected to a mains socket outlet with a 

protective earthing connection.

PWR   STATUS

SERVICE

PORT

Front View 

of Rack Cabinet

1 inch minimum

1 inch minimum

Summary of Contents for CodePlus OAT100R












































































Reviews: