0000000
0000000
0000000
0000000
0000000
0000000
000
000
000
000
000
000
000
000
000
000
000
000
000
000
000
1.8-inch
filler panel
Release
latch
Drive tray
handle
Step 4.
If you are instructed to return the drive assembly, follow all packaging instructions, and use any
packaging materials for shipping that are supplied to you.
Replacing 2.5-inch and 1.8-inch hot-swap drives
Use this information to replace a 2.5-inch or 1.8-inch drive.
The following notes describe the type of drives that the server supports and other information
that you must consider when you install a drive. For a list of supported drives, see
http://www.ibm.com/servers/eserver/serverproven/compat/us/.
• Locate the documentation that comes with the drive and follow those instructions in addition to the
instructions in this chapter.
• Make sure that you have all the cables and other equipment that are specified in the documentation that
comes with the drive.
• The server can support up to 16 2.5-inch drives, up to 32 1.8-inch drives, or a combination of both
2.5-inch and 1.8-inch hot-swap drives, using the supported SAS\SATA backplane configurations. The
server supports 2.5-inch hot-swap SAS or hot-swap SATA hard disk drives, 2.5-inch hot-swap solid state
drives, or 1.8-inch hot-swap solid state drives (see “Supported SAS/SATA drive backplane configurations”
on page 57 for more information).
• You can mix 2.5-inch hot-swap SAS and SATA hard disk drives, 2.5-inch hot-swap solid state drives, and
1.8-inch hot-swap solid state drives in the same server as long as they are not on the same array.
• When upgrading drive backplane configurations, all 1.8-inch solid state drive backplanes must be installed
to the right of all 2.5-inch HDD or 2.5-inch solid state drive backplanes. All 2.5-inch backplanes installs to
the left of all 1.8-inch backplanes. See “Drive IDs” on page 56 for drive ID assignment information and
“Supported SAS/SATA drive backplane configurations” on page 57 for information about the combination
of supported drive backplane configurations.
• The electromagnetic interference (EMI) integrity and cooling of the server are protected by having all bays
and PCI and PCI Express slots covered or occupied. When you install a drive, save the EMC shield and
filler panel from the bay in the event that you later remove the device.
• For a complete list of supported optional devices for the server, see
http://www.ibm.com/servers/eserver/serverproven/compat/us/.
To install a hot-swap drive, complete the following steps:
Step 1.
Read the safety information, see “Safety” on page v and “Installation guidelines” on page 38.
Step 2.
Touch the static-protective package that contains the drive to any unpainted metal surface on the
server; then, remove the drive from the package and place it on a static-protective surface.
226
Lenovo System x3750 M4 Installation and Service Guide
Summary of Contents for System x3750 M4
