Lenel DirecDoor Installation Manual Download Page 88

Page: 88 / 90

Index

DirecDoor Installation Guide

I/O expansion

........................................... 30, 47

ICT requirements

............................................ 63

Information form

............................................. 67

Input LEDs

....................................................... 34

Inserting and removing the UCSIMMPlus

board

.................................................

Integrated Configuration Tool (ICT)

........... 63

Integrated Configuration Tool, disable

........ 72

Integrated Configuration Tool, enable

......... 72

Intelligent system controller (3300)

overview

................................................... 61

LED indicators

................................................ 32

LED normal state transitions

........................ 33

Low battery

...................................................... 26

Maintenance

..................................................... 86

Maximum peripheral loads

...........................

Mounting and handling guidelines

..............

Mounting instructions

.................................... 18

Mounting template

.......................................... 19

Network connection, RJ45

............................ 31

Noise prevention

............................................. 17

NX bus

.............................................................. 30

Other Parameters form

................................... 71

Parameters form

.............................................. 66

Power input port

.............................................. 23

Power LED

......................................................

Power over Ethernet

....................................... 24

Power problems

..............................................

Power requirements

........................................ 20

Primary Network form

................................... 68

Radio interference

........................................... 16

Reader interface

.............................................. 37

Reader problems

............................................. 84

Reader wiring

.................................................. 39

Regulatory information

.................................. 77

Relay for fault output

..................................... 26

Relay power

..................................................... 39

RS485 expansion port

.................................... 30

Saving configuration changes

....................... 66

Secondary Network form

..............................

Signal transmission

......................................... 17

Specifications

.................................................. 10

Supervised DI/REX

........................................ 38

SW3

................................................................... 29

Switches

...........................................................

T-5xx Series Reader

.......................................

Tamper

.............................................................. 32

Tamper switch

.................................................

Testing the Controller

..................................... 61

Testing the DirecDoor controller

.................

UCSIMMPlus Board LEDs

..........................

UL approved system configuration

.............

UL Compliance

............................................... 80

Upstream communications

............................ 36

Wattage calculator

..........................................

WEEE

............................................................... 80

Wiring to Wiegand readers, door contacts,

and exit request

...............................

Summary of Contents for DirecDoor



























































































Search results

Summary of Contents for DirecDoor

Reviews:

Related manuals for DirecDoor

Brands by name

Popular brands

Lenel DirecDoor, Installation Manual

Search results

Summary of Contents for DirecDoor

Reviews:

Related manuals for DirecDoor

Brands by name

Popular brands