Lenel DirecDoor Installation Manual Download Page 24

Page: 24 / 90

Power

DirecDoor Installation Guide

Installing the PoE (Power over Ethernet)

Note:

PoE is not verified for UL installations.

Install the PoE in accordance with manufacturer’s instructions.

Note:

The PoE source must meet IEEE802.3af 16 watt Class 0 Mode A or B Power over
Ethernet Power Sourcing Equipment (PoE/PSE) specifications.

Attach the supplied ferrite to the network cable as shown in figure

Installing Ferrite

on page

Connect the network cable to J10 on the DirecDoor board.

Note:

By Ethernet standards, the maximum cable length is limited to 328 ft. (100 m) between
the PoE source and the DirecDoor controller.

Connect the other end of the network cable to the PoE per the manufacturer’s instructions.

Note:

The DDSDC does not have the following hardware components as shown in the figure
below: Connectors J4, J5, J7 and J11, and Switch SW3.

Installing the PoE (Power over Ethernet)

Summary of Contents for DirecDoor



























































































Search results

Summary of Contents for DirecDoor

Reviews:

Related manuals for DirecDoor

Brands by name

Popular brands

Lenel DirecDoor, Installation Manual

Search results

Summary of Contents for DirecDoor

Reviews:

Related manuals for DirecDoor

Brands by name

Popular brands