![background image](http://html1.mh-extra.com/html/lancer/bevariety-mcy-22/bevariety-mcy-22_installation-and-service-manual_3500568012.webp)
12
28-0724/02
1.
INSTALLATION
1.1
SELECTINg A LOCATION
Make sure the location meets these requirements:
• Access to a grounded 110 Volt, 20 AMP electrical outlet.
• Convenient to an open drain with adequate room to route soda, water, and syrup lines.
• Sufficient clearance above the dispenser for servicing.
• Counter can support the weight of the dispenser, the weight of the ice, and if necessary, an
icemaker. The total weight may exceed 800 pounds (363 kg).
• Sufficient clearance on the sides, top and back for ventilation and air circulation. Refer to your
icemaker for specifications.
• If an icemaker is not top-mounted on the dispenser, make sure to provide sufficient clearance
(a minimum of 16 inches (40.6 cm)) to allow filling the dispenser with ice from a five gallon
(19 liter) container. See figure next page.
• Avoid direct sunlight and other heat sources.
1.2
THINgS TO CONSIDER
Unit may be installed directly on the countertop or on legs. If installed directly on the counter,
the unit must be sealed to the countertop. If an icemaker is to be mounted on top of dispenser,
do not install dispenser on legs.
NOTE:
Water pipe connections and fixtures directly connected
to a potable water supply must be sized, installed, and maintained according to Federal, State,
and Local laws.
• The water supply must be protected by means of an air gap, a backflow prevention device
(located prior to the CO2 injection system) or another approved method to comply with NSF
standards. A backflow prevention device must comply with ASSE and local standards. It is the
responsibility of the installer to ensure compliance.
• Refer to specific icemaker model for proper air intake/exhaust ventilation with Lancer units.
• Install the icemaker per manufacturer specifications. Points of consideration include drainage,
ventilation, and drop zones.
• An adapter plate is required when installing an icemaker. Contact your Sales Representative
or Lancer Customer Service for more information.
• Ensure the icemaker is installed properly to allow for removal of the merchandiser.
• Ensure manual fill is accessible.
• Clean and maintain icemaker per manufacturer’s instructions.
• When installing an icemaker on an IBD unit, a bin thermostat or other means of controlling
the ice level must be installed. Failure to do so could result in damage to the dispensing
mechanism and void the warranty.
• During the automatic agitation cycle and/or while dispensing ice, there must be adequate
room between the top of the ice level and the bottom of the icemaker so the ice can move
without obstruction.
• Contact your icemaker supplier for information on a proper bin thermostat.
• Use of a water filtration system is recommended.
• Water filtration system must be maintained and inspected periodically.
• Location must ensure sufficient clearance on sides, top and back of unit for ventilation and air
circulation of the icemaker. Additionally, if an icemaker is not top-mounted on the unit,
sufficient clearance should be provided (a minimum of 16 inches (40.6 cm) is recommended)
to allow filling the unit with ice from a five gallon (19 liter) container.
Summary of Contents for BEVARIETY MCY-22
