Keithley 2701 Service Manual Download Page 159

Page: 159 / 168

B-20

Calibration Reference

Model 2701 Service Manual

:LOCK

(:CALibration:PROTected:CARD1:LOCK)

Purpose

To lock out Model 7700 calibration.

Format

:cal:prot:card1:lock

Parameter

None

Description

The

:LOCK

command allows you to lock out Model 7700 calibration after

completing the procedure. Thus,

:LOCK

performs the opposite of enabling

calibration with the

:CODE

command.

Example

:CAL:PROT:CARD1:LOCK

Lock out card 1 calibration.

:LOCK?

(:CALibration:PROTected:CARD1:LOCK?)

Purpose

To read Model 7700 calibration lock status.

Format

:cal:prot:card1:lock?

Response

Calibration locked.

Calibration unlocked.

Description

The

:LOCK?

query requests status from the Model 2701 on Model 7700

calibration locked/unlocked state. Calibration must be enabled sending the

:CODE

command before calibration can be performed.

Example

:CAL:PROT:CARD1:LOCK?

Request card 1 cal lock state.

:RCOunt

(:CALibration:PROTected:CARD1:RCOunt)

Purpose

To reset card calibration count to 0.

Format

:cal:prot:card1:rco

Parameter

None

Description

The

:RCOunt

command resets the card calibration count reported by

:COUNt?

to 0.

Example

:CAL:PROT:CARD1:RCO

Rest card calibration count.

Summary of Contents for 2701









































































































































































Search results

Summary of Contents for 2701

Reviews:

Related manuals for 2701

Brands by name

Popular brands

Keithley 2701, Service Manual

Search results

Summary of Contents for 2701

Reviews:

Related manuals for 2701

Brands by name

Popular brands