Keithley 2701 Service Manual Download Page 132

Page: 132 / 168

Keithley Instruments, Inc.

Cleveland, Ohio 44139

DRN.
CKD.
APP.

DATE
DATE
DATE

PART NUMBER

LTR

REVISIONS

APP. DATE

FORM 28777A-SBG

BRUNING 40-21 62198-SBG

PURCHASED ITEM

SPECIFICATIONS

HW 8/01/02

Revision A

Page 1 of 3

2701 Ethernet Multimeter/Data Acquisition System

DC CHARACTERISTICS

CONDITIONS: MED (1 PLC)

or 10 PLC or MED (1 PLC) with Digital Filter of 10

TEST

INPUT

ACCURACY: ±(ppm of r ppm of range)

CURRENT ±5%

RESISTANCE

(ppm = parts per million) (e.g., 10ppm = 0.001%)

TEMPERATURE

OR BURDEN

OR OPEN CKT.

24 Hour

90 Day

1 Year

COEFFICIENT

FUNCTION

RANGE

RESOLUTION

VOLTAGE

23°C±1°

23°C±5°

0°–18°C & 28°–50°C

Voltage

100.0000 mV

0.1 µV

>10 G

Ω

15 + 30

25 + 35

30 + 35

(1 + 5)/°C

1.000000

1.0 µV

>10 G

Ω

15 + 6

25 + 7

30 + 7

(1 + 1)/°C

10.00000

10 µV

>10 G

Ω

10 + 4

20 + 5

30 + 5

(1 + 1)/°C

100.0000

100 µV

10 M

Ω

± 1%

15 + 6

35 + 9

45 + 9

(5 + 1)/°C

1000.000

1 mV

10 M

Ω

± 1%

20 + 6

35 + 9

50 + 9

(5 + 1)/°C

Resistance

6, 8

100.0000

Ω

100 µ

Ω

1 mA

6.9 V

20 + 20

80 + 20

100 + 20

(8 + 1)/°C

1.000000 k

Ω

1 m

Ω

1 mA

6.9 V

20 + 6

80 + 6

100 + 6

(8 + 1)/°C

10.00000 k

Ω

10 m

Ω

100 µA

6.9 V

20 + 6

80 + 6

100 + 6

(8 + 1)/°C

100.0000 k

Ω

100 m

Ω

10 µA

12.8 V

20 + 6

80 + 10

100 + 10

(8 + 1)/°C

1.000000 M

Ω

1.0

Ω

10 µA

12.8 V

20 + 6

80 + 10

100 + 10

(8 + 1)/°C

10.00000 M

Ω

0.7 µA // 10M

Ω

7.0 V

150 + 6

200 + 10

400 + 10

(70 + 1)/°C

100.0000 M

Ω

100

Ω

0.7 µA // 10M

Ω

7.0 V

800 + 30

2000 + 30

(385 + 1)/°C

Continuity (2W)

1.000 k

Ω

100 m

Ω

1 mA

6.9 V

40 + 100

100 + 100

(8 + 1)/°C

Current

20.00000 mA

10 nA

< 0.2

60 + 30

300 + 80

500 + 80

(50 + 5)/°C

100.0000 mA

100 nA

< 0.1

100 + 300

300 + 800

500 + 800

(50 + 50)/°C

1.000000

1.0 µA

< 0.5

200 + 30

500 + 80

800 + 80

(50 + 5)/°C

3.000000

10 µA

< 1.5

1000 + 15

1200 + 40

(50 + 5)/°C

Channel (Ratio)

Ratio Accuracy = Accuracy of selected Channel Range + Accuracy of Paired Channel Range

Channel (Average)

Average Accuracy = Accuracy of selected Channel Range + Accuracy of Paired Channel Range

TEMPERATURE

(Displayed in °C, °F, or K. Exclusive of probe errors.)

Thermocouples (Accuracy based on ITS-90.)

90 Day/1 Year (23°C ± 5°C)

Relative to

Using

Temperature

Simulated

77xx

Coefficient

Type

Range

Resolution Reference Junction

Module

0°–18°C & 28°–50°C

–200 to +760 °C

0.001°C

0.2°C

1.0°C

0.03°C/°C

–200 to +1372°C

0.001°C

0.2°C

1.0°C

0.03°C/°C

–200 to +1300°C

0.001°C

0.2°C

1.0°C

0.03°C/°C

–200 to +400°C

0.001°C

0.2°C

1.0°C

0.03°C/°C

–200 to +1000°C

0.001°C

0.2°C

1.0°C

0.03°C/°C

0 to +1768°C

0.1

°C

0.6°C

1.8°C

0.03°C/°C

0 to +1768°C

0.1

°C

0.6°C

1.8°C

0.03°C/°C

+350 to +1820°C

0.1

°C

0.6°C

1.8°C

0.03°C/°C

4-Wire RTD:
(100

Ω

platinum [PT100], D100, F100, PT385, PT3916, or user type. Offset compensation On)

–200° to

630°C

0.01 °C

0.06°C

0.003°C/°C

Thermistor: (2.2k

Ω

, 5k

Ω

, and 10k

Ω

)

–80° to

150°C

0.01 °C

0.08°C

0.002°C/°C

DC SYSTEM SPEEDS

15,18

RANGE CHANGES

50/s (42/s) (excludes 4 Wire Ohms).

FUNCTION CHANGES

50/s (42/s).

AUTORANGE TIME

<30ms.

ASCII READINGS TO RS-232 (115.2k BAUD):

300/s.

MAX. EXTERNAL TRIGGER RATE:

2000/s.

DC MEASUREMENT SPEEDS

Single Channel, 60Hz (50Hz) Operation

FUNCTION

DIGITS

READINGS/s

PLCs

DCV, DCI,

Ω

(<10M),

6.5

12,16

(4)

Thermocouple,

6.5

(28)

Thermistor

6.5

12,16

(48)

5.5

12,16

150

(120)

0.1

5.5

16, 17

300

(240)

0.1

5.5

500

(400)

0.1

4.5

3000 (3000)

0.006

3.5

3500 (3500)

0.002

Ω

(<10M)

6.5

1.4

(1.1)

6.5

(12)

5.5

16, 17

(25)

0.1

Ω

OComp, RTD

6.5

16, 17

0.9

(0.7)

6.5

16, 17

(6.4)

5.5

16, 17

18 (14.4)

0.1

Channel (Ratio),

6.5

16, 17

2.5

(2)

Channel (AVG)

6.5

16, 17

(12)

5.5

16, 17

(20)

0.1

Multiple Channels Into Memory

15, 18

7710 Scanning DCV

500/s

7703 Scanning DCV

390/s

7703 Scanning DCV with Limits or Time Stamp On

390/s

7703 Scanning DCV alternating 2W

Ω

95/s

Multiple Channels, Into and Out of Memory

15, 16, 17, 18

Channels/s

7710 Scanning DCV

440/s

7703 Scanning DCV

360/s

7703 Scanning DCV with Limits or Time Stamp On

360/s

7703 Scanning DCV alternating 2W

Ω

90/s

7702 Scanning DCV

75/s

7700 and 7708 Scanning Temperature (T/C)

60/s

SPEC-2701

Summary of Contents for 2701









































































































































































Search results

Summary of Contents for 2701

Reviews:

Related manuals for 2701

Brands by name

Popular brands

Keithley 2701, Service Manual

Search results

Summary of Contents for 2701

Reviews:

Related manuals for 2701

Brands by name

Popular brands