Kaixin DCU10 Operation Manual Download Page 67

Page: 67 / 102

Page 66 of 101

Press the PW key on the control panel to enter the PW mode.

Press the Caliper key to activate the measurement, and the measurement menu displays on the

top

left of the screen.

Select [HR] on the menu by moving the trackball and press Set to confirm. A marker displays on

the image.

Move the marker to the starting point by using the trackball, press Set to fix the marker and the

second

marker displays.

Move the second marker to the end point by using the trackball and press Set. The measurement

result

displays in the result box.

8.4.3.5 Acceleration

It is used to calculate the flow speed difference in the time interval from two measured flow speeds

on the

PW mode image.

Steps:

Press the PW key on the control panel to enter the PW mode.

Press the Caliper key to activate the measurement, and the measurement menu displays on the

top left of

the screen.

Select [Acceleration] on the menu by moving the trackball and press Set to confirm. A marker

displays on the

image.

Move the marker to the starting point by using the trackball, press Set to fix the marker and the

second

marker displays.

Move the second marker to the end point by using the trackball and press Set. The measurement

result

displays in the result box.

8.4.3.6 Spectrum Trace

It used to measure the velocity or other indexes for clinical diagnosis purposes by tracing one or

more Doppler waveforms. Manual trace and auto trace are available.

To ensure the measurement accuracy, you should position the first marker on peak systole and

position the second marker on end diastole during the trace measurements.

Spectrum trace can only be performed in frozen PW mode.

Manual trace

Steps:

Press the PW key on the control panel enter the PW mode, then press Freeze key.

Press the Caliper key to activate the measurement, and the measurement menu displays on

the top left of

the screen.

Select [D Trace] on the menu by moving the trackball and press Set to confirm.

Select[Manual] on the pop-up menu. A marker displays on the image.

Move the marker to the starting point of peak waveform of the end systole by using the

trackball, press Set to fix the marker and the second marker displays.

Trace the waveform and move the second marker to the end diastole which is one cardiac

cycle adjacent to

the first marker by using the trackball and press Set. The measurement

result displays in the result box.

Auto trace

Steps:

Press the PW key on the control panel to enter the PW mode, then press Freeze key.

Press the Caliper key to activate the measurement, and the measurement menu displays on

the top left

of the screen.

Summary of Contents for DCU10







































































































Search results

Summary of Contents for DCU10

Reviews:

Kaixin DCU10, Operation Manual, Page: 67 / 102

Search results

Summary of Contents for DCU10

Reviews: