Kaixin DCU10 Operation Manual Download Page 65

Page: 65 / 102

Page 64 of 101

Press the Caliper key to activate the measurement, and the measurement menu displays on the

top

left of the screen.

Select [Distance] on the menu by moving the trackball and press Set to confirm. A

marker

displays on the image.

Move the marker to the starting point by using the trackball, press Set to fix the marker and the

second marker displays.You can also press Update on the control panel, move the trackball to adjust the

starting point.

Move the second marker to the end point by using the trackball and press Set. A line connects

these two points. The measurement result displays in the result box.

Repeat step 3-5 to perform the next distance measurement.

8.4.2.2 Time

It is used to measure the time interval between two points on the M mode image.

Steps:

Press the M key on the control panel to enter the M mode.

Press the Caliper key to activate the measurement, and the measurement menu displays on the top

left of the screen.

Select [Time] on the menu by moving the trackball and press Set to confirm. A marker displays

on the

image.

Move the marker to the starting point by using the trackball, press Set to fix the marker and the

second marker displays.

Move the second marker to the end point by using the trackball and press Set. The measurement

result

displays in the result box.

8.4.2.3 Heart Rate

It is used to measure the time interval between heart cycles based on the number of heartbeats per

minute on the M mode image.

You can preset the heart cycle in [Preset] -> [Measure Preset] -> [HR].

Steps:

Press the M key on the control panel to enter the M mode.

Press the Caliper key to activate the measurement, and the measurement menu displays on the

top left of the screen.

Select [HR] on the menu by moving the trackball and press Set to confirm. A marker displays on

the image.

Move the marker to the starting point by using the trackball, press Set to fix the marker and the

second marker displays.

Move the second marker to the end point by using the trackball and press Set. The measurement

result

displays in the result box.

8.4.2.4 Slope Rate

It is used to measure the change in distance over time on the M mode image.

Steps:

Press the M key on the control panel to enter the M mode.

Press the Caliper key to activate the measurement, and the measurement menu displays on the

top

left of the screen.

Select [Slope] on the menu by moving the trackball and press Set to confirm. A marker displays

on the image.

Move the marker to the starting point by using the trackball, press Set to fix the marker and the

second marker displays.

Move the second marker to the end point by using the trackball and press Set. The measurement result

displays in the result box.

Summary of Contents for DCU10







































































































Search results

Summary of Contents for DCU10

Reviews:

Kaixin DCU10, Operation Manual, Page: 65 / 102

Search results

Summary of Contents for DCU10

Reviews: