Kaixin DCU10 Operation Manual Download Page 60 | Manualshive

Page: 60 / 102

Kaixin DCU10 Operation Manual Download Page 60

Page 59 of 101

8.2 Measurement Menu

Caliper Measure

Figure 8-2 Measurement Menu

The measurement menu consists of exam type, measurement items and measurement sub-items.

Exam Type
The name of the exam type is displayed. You can select it on the Probe and Exam Type screen. The
measurement items vary with the exam type.

Measurement Items and Sub-items
The measurement items display under the exam type. >> after a measurement item indicates you can
select it to display the sub-items. Move the trackball on this measurement item and press the

Set

key

to display them.
Measurement items and sub-items also display in the toolbar. You can press the corresponding
buttons to activate it. The following sections are described according to the measurement menu.

8.3 Measurement Error

Ultrasound scan and measurements are highly precise, but the measurement errors can still exist due

to the

«
...
58
59
60
61
62
...
»

Summary of Contents for DCU10







































































































Reviews:

No comments