Kaixin DCU10 Operation Manual Download Page 45

Page: 45 / 102

Page 44 of 101

6.2.2.9 Adjusting the frame average

Frame average is used to average consecutive frames to provide a smoother appearance with less noise.

Use lower frame average values for fast-moving organs or tissues and higher persistence values for

smoother appearance.

Steps:

Move cursor to [Frame Average] menu item and press Set key to adjust it.

Rotate Select knob to highlight the [

Frame Average

] menu item, press Select knob item to confirmation

select [

Frame Average

] item, and then Rotate Select knob to adjust it.

6.2.2.10 Adjusting the Scan Density

Density improves the resolution and decreases frame rate. Therefore, you have to balance the frame rate and

the image quality when adjusting the line density.

Steps:

Move cursor to [Scan Density] menu item and press Set key to adjust it.

Rotate Select knob to highlight the [Scan Density] menu item, press Select knob item to confirmation

select [Scan Density] item, and then Rotate Select knob to adjust it.

6.2.2.11 Adjusting the Steer Angle

Steer angle is used to adjust the angle of the color ROI.

Steps:

Move cursor to [Steer] menu item and press Set key to adjust the angle of the ROI.

Rotate Select knob to highlight the [Steer] menu item, press Select knob item to confirmation select

[Steer] item, and then Rotate Select knob to adjust the angle of the ROI.

Press Steer- or Steer+ key to decrease or increase the angle of the ROI

The feature is only available with the linear probe.

6.2.2.12 Adjusting the Color Map

Color map is used to select the method for the color-coding of blood flows.

For the color flow image, the change of the color tone represents the change of the speed rate. Darker

color tone represents the lower speed rate and vice versa. And the red and blue color represent the

different flow direction respectively.

Steps:

Move cursor to [Color Map] menu item and press Set key to change the color.

Rotate Select knob to highlight the [Color Map] menu item, press Select knob item to confirmation

select [Color Map] item, and then Rotate Select knob to change the color.

6.2.2.13 Adjusting the Post-Process

Post-process is used to optimize the quality of the image.

Steps:

Move cursor to [Post Proc] menu item and press Set key to adjust it.

Rotate Select knob to highlight the [Post Proc] menu item, press Select knob item to confirmation

select [Post Proc] item, and then Rotate Select knob to adjust it.

Summary of Contents for DCU10







































































































Search results

Summary of Contents for DCU10

Reviews:

Kaixin DCU10, Operation Manual, Page: 45 / 102

Search results

Summary of Contents for DCU10

Reviews: