Kaixin DCU10 Operation Manual Download Page 66

Page: 66 / 102

Page 65 of 101

8.4.3 PW Mode Measurements

Flow sweep ratio, speed, time, heart rate, acceleration and spectrum trace measurements can be

performed in

the PW mode. You can also press [BC General Measurements] to enter the general

measurements in the 2D

mode. For details, please refer to Section 8.5.1 2D Mode Measurements.

8.4.3.1 Flow Speed Ratio

It is used to calculate the flow speed ratio and Pressure Gradient (PG) on the Doppler-mode image

measuring the flow speed of peak systole and end diastole.

Step:

Press the PW key on the control panel to enter the PW mode.

Press the Caliper key to activate the measurement, and the measurement menu displays on the

top

left of the screen.

Select [S/D] on the menu by moving the trackball and press Set to confirm. A marker displays on

the image.

Move the marker to the flow speed of peak systole by using the trackball, press Set to fix the

marker and the second marker displays.

Move the second marker to the flow speed of end diastole by using the trackball and press Set.

The measurement result displays in the result box.

8.4.3.2 Speed

It is used to measure the speed of one point on the spectral Doppler waveform.

Press the PW key on the control panel to enter the PW mode.

Press the Caliper key to activate the measurement, and the measurement menu displays on the

top left of

the screen.

Select [Velocity] on the menu by moving the trackball and press Set to confirm. A marker

displays on the image.

Move the marker to the desired point by using the trackball and press Set. The measurement

result displays in the result box.

8.4.3.3 Time

It is used to measure the time interval between two points on the spectral Doppler image.

Steps:

Press the PW key on the control panel to enter the PW mode.

Press the Caliper key to activate the measurement, and the measurement menu displays on the

top

left of the screen.

Select [Time] on the menu by moving the trackball and press Set to confirm. A marker displays

on the image.

Move the marker to the starting point by using the trackball, press Set to fix the marker and the

second marker displays.

Move the second marker to the end point by using the trackball and press Set. The measurement

result

displays in the result box.

8.4.3.4 Heart Rate

It is used to measure the time interval between heart cycles based on the number of heartbeats per

minute on the PW mode image.

Steps:

Summary of Contents for DCU10







































































































Search results

Summary of Contents for DCU10

Reviews:

Kaixin DCU10, Operation Manual, Page: 66 / 102

Search results

Summary of Contents for DCU10

Reviews: