Kaixin DCU10 Operation Manual Download Page 54

Page: 54 / 102

Page 53 of 101

The feature is only available with the linear probe.

6.5.2.10 Adjusting the Chroma

Chroma is used to colorize the grayscale image.

Steps:

Move cursor to [Colorize] menu item and press Set key to adjust it.

Rotate Select knob to highlight the [Colorize] menu item, press Select knob item to confirmation select

[Colorize] item, and then Rotate Select knob to adjust it.

6.5.2.11 Adjusting the Wall Filter

Wall filter is used to filter the low frequency noise from the tissue activities of the patient and clear

the fake image.

Steps:

Move cursor to [Wall Filter] menu item and press Set key to adjust it.

Rotate Select knob to highlight the [Wall Filter] menu item, press Select knob item to confirmation

select [Wall Filter] item, and then Rotate Select knob to adjust it.

6.5.2.12 Adjusting the Dynamic Range

Dynamic range increases the adjustable range of contrast by enhancing the intensities of parts of the grayscale.

Steps:

Move cursor to [Dynamic Ra.] menu item and press Set key to adjust it.

Rotate Select knob to highlight the [Dynamic Ra.] menu item, press Select knob item to confirmation

select [Dynamic Ra.] item, and then Rotate Select knob to adjust it.

6.5.2.13 Enabling/Disabling the Full-Screen Display

Full-screen display is used to display the image in full screen.

Steps:

Move cursor to [Dynamic Ra.] menu item and press Set key to adjust it.

Rotate Select knob to highlight the [Dynamic Ra.] menu item, press Select knob item to confirmation

select [Dynamic Ra.] item, and then Rotate Select knob to adjust it.

6.5.2.14 Adjusting the Acoustic Power

Acoustic power is adjusted to increase or decrease the transmitting frequency of the probe.

Steps:

Move cursor to [A. Power] menu item and press Set key to adjust it.

Rotate Select knob to highlight the [A. Power] menu item, press Select knob item to confirmation

select [A. Power] item, and then Rotate Select knob to adjust it.

6.5.2.15 Adjusting the Spectrum Smoothness

Spectrum smoothness is used to decrease the spectrum noise and make the image display smoother.

Steps:

Move cursor to [Smooth] menu item and press Set key to adjust it.

Rotate Select knob to highlight the [Smooth] menu item, press Select knob item to confirmation select

[Smooth] item, and then Rotate Select knob to adjust it.

Summary of Contents for DCU10







































































































Search results

Summary of Contents for DCU10

Reviews:

Kaixin DCU10, Operation Manual, Page: 54 / 102

Search results

Summary of Contents for DCU10

Reviews: