Kaixin DCU10 Operation Manual Download Page 64

Page: 64 / 102

Page 63 of 101

Move the marker to the starting point by using the trackball, press Set to fix the marker and

the second

marker displays.

Move the second marker along the target object by using the trackball.

Press Set to confirm.

Repeat step 2-5 to perform a second trace measurement. The system automatically calculates

the trace ratio,

and the measurement result displays in the result box.

8.4.1.5 Distance Ratio

It is used to measure the value of distance ratio between two lines.

Steps:

Press the Caliper key to activate the measurement, and the measurement menu displays on the

top

left of the screen.

Select [Ratio(D)] on the menu by moving the trackball and press Set to confirm. A

marker

displays on the image.

Move the marker to the starting point by using the trackball, press Set to fix the marker and the

second marker displays.

You can also press Update on the control panel, move the trackball to adjust the starting point.

Move the second marker to the end point by using the trackball and press Set. A line connects

these two points.

Repeat step 3-5 to perform a second distance measurement. The system automatically calculates

the

distance ratio, and the measurement result displays in the result box.

8.4.1.6 Angle

It is used to measure the value of angle between two intersection planes.

Steps:

Press the Caliper key to activate the measurement, and the measurement menu displays on the

top

left of the screen.

Select [Angle] on the menu by moving the trackball and press Set to confirm. A marker displays

on the

image.

Move the marker to the starting point by using the trackball, press Set to fix the marker and the

second marker displays.

You can also press Update on the control panel, move the trackball to adjust the starting point.

Move the second marker to the end point by using the trackball and press Set. A line connects

these two points.

Repeat step 3-5 to draw a second line to create an angle. The system automatically calculates the

angle,

and the measurement result displays in the result box.

8.4.2 M Mode Measurements

Distance, time, heart rate and slope measurements can be performed in the M mode. You can also

press [BC Caliper] to enter the general measurements in the 2D mode. For details, please refer to

Section 8.4.1 2D Mode Measurements.

8.4.2.1 Distance

It is used to measure the vertical distance between two points on the M mode image.

Steps:

Press the M key on the control panel to enter the M mode.

Summary of Contents for DCU10







































































































Search results

Summary of Contents for DCU10

Reviews:

Kaixin DCU10, Operation Manual, Page: 64 / 102

Search results

Summary of Contents for DCU10

Reviews: