K-sun Green Machine User Manual Download Page 7 | Manualshive

Page: 7 / 142

background image

Introduction

1

Important Safety Precautions

Items below should always be followed to protect users, their surroundings and their
property from possible injury or damage. Be sure to read and understand the
instructions before using your K-Sun® GREEN MACHINE

®

and keep this manual handy

for future references.

●

Precautionary notations throughout the text are categorized relative to 1) personal injury
and 2) damage to equipment.

●

Please familiarize yourself with the following definitions and meanings for each symbol
before reading the precautions.

DANGER

Signals a precaution which, if ignored, will result in serious
or fatal personal injury. Pay extra caution in performing
procedures preceded by DANGER headings.

WARNING

Signals a precaution which, if ignored, could result in
serious or fatal personal injury.

CAUTION

Signals a precaution which, if ignored, could result in
damage to equipment.

Important reminder

Prohibited

Mandatory

DANGER

When using the battery

If liquid leaking from the battery gets into your eyes, do not rub your
eyes. Wash them well with clean water and contact a doctor
immediately.

«
...
5
6
7
8
9
...
»

Summary of Contents for Green Machine















































































































































Reviews:

No comments

Related manuals for Green Machine

Brand: Rancilio Pages: 60

Brand: Rancilio Pages: 14

Brand: Hotpoint Pages: 8

Brand: White and Brown Pages: 16

Brand: Euro Cuisine Pages: 28

Brand: DeLonghi Pages: 10

FUTURMAT SENSIUS

Brand: Quality Espresso Pages: 44

Brand: Krups Pages: 56

Brand: Fagor Pages: 14

Brand: Saeco Pages: 40

Brand: Hamilton Beach Pages: 72

Brand: Lagrange Pages: 66

Brand: Cloer Pages: 32

Brand: Nuova Simonelli Pages: 14

Brand: Nuova Simonelli Pages: 11

Brand: Nuova Simonelli Pages: 14

Brand: Nuova Simonelli Pages: 32

Brand: Nuova Simonelli Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands