K-sun Green Machine User Manual Download Page 28 | Manualshive

Page: 28 / 142

background image

Getting Started

22

Close the top cover.

Close the cover gently.

Removing the tape cartridge

To ensure proper and beautiful printing, the tape
cartridge is secured to the main unit firmly. To
remove, place your fingers on the tabs provided
on both sides of the cartridge as shown in the
figure, lift the tabs straight up to pull out the
cartridge.

•

If you close the top cover without entirely inserting the tape cartridge completely, your K-Sun

®

GREEN MACHINE

®

or the tape cartridge may be damaged.

•

K-Sun

®

GREEN MACHINE

®

supports six different tape cartridge widths: 1/6", 1/4", 3/8",

1/2",3/4", 1". Number of lines printed on the tape varies depending the tape width.

See

"Adding New Lines (Line Break)" (p.44).

•

Tape cartridges should be stored in a dark cold place away from direct sunlight,
excessive temperature and humidity, and dust.

•

It is recommended that you use the tape cartridge as soon as possible after opening.

•

When installing the tape cartridge, insert it firmly as far as it can go.

•

When the tape cartridge that is not supported by the K-Sun

®

GREEN MACHINE

®

is

installed, a message; "Check Tape!" or "No Tape!" appears. Reinstall the supported tape
cartridge properly.

4

•

If you close the top cover without entirely
inserting the tape cartridge completely, your
K-Sun

®

GREEN MACHINE

®

or the tape

cartridge may be damaged.

•

Make sure the top cover is completely
closed.

Tabs

22

Getting Started

«
...
26
27
28
29
30
...
»

Summary of Contents for Green Machine















































































































































Reviews:

No comments

Related manuals for Green Machine

Brand: La San Marco Pages: 24

LOOK Selection DeLuxe 1011

Brand: Melitta Pages: 45

Brand: Ninja Pages: 11

Brand: U-Line Pages: 44

Brand: Igloo Pages: 30

Brand: Lynx Pages: 28

Brand: Kogan Pages: 4

Brand: SOLAC Pages: 36

Brand: Victoria Arduino Pages: 54

Brand: ibingo Pages: 12

Brand: Johny Pages: 4

The Ripple Maker

Brand: Steam Pages: 20

Brand: Melitta Pages: 38

Brand: Getinge Pages: 4

Brand: Costway Pages: 12

VIVA PRESTIGE RI84 Series

Brand: Gaggia Milano Pages: 156

Brand: Ice-O-Matic Pages: 30

Brand: Royal Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands