manualshive.com logo in svg

IOtech MultiScan 1200, User Manual

Share
Download
IOtech MultiScan 1200 User Manual Download Page 158

148     Chapter 10: PostView

TempScan / MultiScan User's Manual

You can choose to manually create a display configuration, or have one created automatically.  The
automatic setup method offers three choices: Simple, Moderate, and Advanced.

A 

Manual Chart Creation, 

Create Charts

 button allows you to bypass the 

Chart Setup Wizard

 and

enter a manual editing mode.  This option makes use of PostView’s Display Configuration feature
(discussed in the following 

Display Configuration

 section).  Manual Chart Creation allows you to vary

the number of assigned channels per chart, as well as vary the number of charts per group.

Chart Setup Wizard, Simple Mode

Chart Setup Wizard, Automatic Setup Options for PostView

Setup Type

Group Setup
(for Chart Groups)

Chart Setup

Channel Setup

Simple

1 group only

Up to 16 charts

1 channel per chart

Moderate

1 group only

Up to 16 charts

Up to 4 overlapping channels per chart

Advanced

Up to 64 groups

Up to 16 charts per group

Up to 4 overlapping channels per chart

Note:

  The 

Manual Charts Creation, Create Charts 

 button (above figure) allows you to exit the 

Chart Setup

Wizard

 and enter the manual 

Display Configuration

 mode.

Automatic Chart Creation

The previous figure shows the Simple mode dialog box for Automatic Chart Creation.  The following
figures show the Moderate and Advanced mode dialog boxes.

Dialog Boxes for Moderate and Advanced Modes of Automatic Chart Creation

Summary of Contents for MultiScan 1200













































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands