IOtech MultiScan 1200 User Manual Download Page 145

Page: 145 / 364

TempScan / MultiScan User's Manual

Chapter 9: TempView 135

Options Menu Items (Charts Only)

Options Menu Items

Stay On Top

(22)

Enables and disables "pinning" the window on top of other windows. This menu item also appears in
any of the Meters

View

menus.

Show Grids

(23)

Adds and removes a grid to your chart.

Print Charts

(24)

Sends the display image to the connected printer. This menu item has the same function as the

Print

menu item in any of the Meters

View

menus.

Number of Charts

(26)

Specifies the number of charts to appear on the screen. This menu item has the same function as the

Number of Meters

menu item in any of the Meters

View

menus.

Summary of Contents for MultiScan 1200













































































































































































































































































































































































Search results

Summary of Contents for MultiScan 1200

Reviews:

Brands by name

Popular brands

IOtech MultiScan 1200, User Manual

Search results

Summary of Contents for MultiScan 1200

Reviews:

Brands by name

Popular brands