manualshive.com logo in svg

IOtech MultiScan 1200, User Manual

Share
Download
IOtech MultiScan 1200 User Manual Download Page 134

124     Chapter 9: TempView

TempScan / MultiScan User's Manual

Status > Instrument Error Status...

Displays a field as an error record of all the TempScan/1100 or MultiScan/1200 system errors in the
current TempView session.  The 

Device Error Status

 dialog box appears when this item is selected,

and its information cannot be changed until it is cleared by the reinitialization of another TempView
session.  Note that this menu item can be selected during, as well as outside, an acquisition.

Device Error Status Dialog Box

(Device > Status > Instrument Error Status…)

Status > Instrument Realtime Clock...

Displays the exact system time and date at which this item is selected.  The 

Device System Time

 dialog

box appears, and allows you to reset any of the following components of the system time: 

Hours, Min

(minutes), Sec (seconds), Tenth (tenths of a second), Month, Day, 

and 

Year.

Device System Time Dialog Box

(Device > Status > Instrument Realtime Clock…)

Summary of Contents for MultiScan 1200













































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands