manualshive.com logo in svg

IOtech MultiScan 1200, User Manual

Share
Download
IOtech MultiScan 1200 User Manual Download Page 133

TempScan / MultiScan User's Manual

Chapter 9: TempView     123

RS-232 Setup Dialog Box

(Device > Interface > Setup RS-232…)

Interface > Simulated Instrument

Starts a new session of TempView without the requirements for hardware connections and
configuration.  During a first-time startup, the 

Simulated Instrument

 option appears in the 

Select

Interface 

dialog box, and is strongly recommended for the beginner as a means to navigate TempView

and inspect its application features without hardware concerns.  Note that if your TempScan/1100 or
MultiScan/1200 is not connected, you must select 

Simulated Instrument

 as your device interface.

Status > Instrument Inventory...

Displays a spreadsheet as a current checklist of the TempScan/1100 or MultiScan/1200 master unit, the
Exp/10A and/or Exp/11A expansion units, as well as the scanning card types and positions.  The

System Inventory

 dialog box appears when this item is selected, and the information on its 

System

Configuration

 spreadsheet cannot be changed.

System Inventory Dialog Box

(Device > Status > Instrument Inventory…)

Summary of Contents for MultiScan 1200













































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands