Huawei 3900 Series Commissioning Manual Download

Page: 187 / 196

The hardware connections are
correct.

Site management rights are
released.

The transmission between the BBU and the

BSC is available.

Remote
Commiss
ioning

The transmission between
BBU and MRFU, BBU and
RRU3908, and BBU and BSC
are normal.

The transmission between the
cascaded GBTSs is normal.

The transmission between the
GBTSs in ring topology is
normal.

The board configuration is
correct and the boards are
working properly.

The active software version is
correct.

The hardware installation and
the data configuration are
consistent with each other.

No alarm related to the GBTS
is reported.

The CS service test is
successful.

The PS service test is
successful.

The environment monitoring
alarm can be reported
normally.

The VSWR is correct. Record
the value of the VSWR.

The output power of the TRX
is normal. Record the value of
the output power per carrier.

The antenna system is properly
connected.

3900 Series Multi-Mode Base Station
Commissioning Guide

7 Commissioning the MBTS by Using Local Maintenance

Terminal and M2000

Issue 02 (2010-07-30)

Huawei Proprietary and Confidential

7-43

Summary of Contents for 3900 Series





































































































































































































Search results

Summary of Contents for 3900 Series

Reviews:

Related manuals for 3900 Series

Brands by name

Popular brands

Huawei 3900 Series, Commissioning Manual

Search results

Summary of Contents for 3900 Series

Reviews:

Related manuals for 3900 Series

Brands by name

Popular brands